Bedienungsanleitung Allen-Heath GL 4000 (Seite 17 von 54) (Englisch)

541356

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

MONO INPUT

+48V - Feeds +48V to pins 2 and 3 of the input XLR for condenser

microphones which require phantom power.

Plug the microphone in before switching +48V on or off. Use +48V

only with balanced microphones and cables. No damage will occur

when +48V is switched to balanced non-phantom powered transformer

coupled dynamic microphones. However, always switch +48V off when

connecting line or unbalanced sources.

PHASE REVERSE - Reverses XLR input pins 2 and 3 to correct for

reverse wired cables or reversed phase signals. Can also be effective in

minimising acoustic feedback between the microphone and loudspeakers

in live sound mixing.

MIC/LINE (PAD) - Selects line input sensitivity when pressed, microphone

when released. Note that with the line jack unplugged the switch acts as

a 20dB pad for high output microphones or line input on XLR.

GAIN - Use this control with the MIC/LINE switch to adjust the channel

input sensitivity to match the connected source (-60 to +14dBu) to the

console operating level (0dBu). The gain should be set so that the channel

meter reads an average '0'.

LO-CUT FILTER - Reduces low frequency source noise such as

microphone proximity popping, stage noise and transport rumble. Can be

used to clean up sounds that do not have much bass content such as

vocals (around 150Hz), separate out the top end of a drum kit (400Hz),

reduce the handling noise of acoustic instruments, and so on. Select the

required cut off frequency by sweeping from fully anticlockwise (filter off)

to the maximum 400Hz. Setting the cutoff to 50Hz will have little effect on

most program material but will protect the low frequency speaker drivers.

The response drops by 12dB per octave below the cut off frequency.

EQUALISER - This provides separate, simultaneous control of 4

frequency bands. Each band may be boosted or cut by up to +/- 15dB

centred on the selected frequency which may be swept across a wide

range. Use the equaliser to correct for tonal deficiencies in the source

such as acoustic resonances or poor microphone response (corrective

EQ), or to change the tonal balance, for example to brighten up a guitar

so it cuts through the mix (effective EQ). You may need to adjust the input

GAIN control when using excessive amounts of EQ to compensate for the

change in overall signal level.

HF and LF affect the high (treble) and low (bass) frequencies respectively.

These have a shelving response which means that all frequencies beyond

the selected frequency are affected.

MF1 and MF2 affect the upper and lower mid frequencies respectively.

These have a peak/dip (bell shaped) response which means that the

maximum boost or cut occurs at the selected (center) frequency. The

MF1 and MF2 bands overlap for additional cut or boost when required or

to provide a tailored frequency response to suit any application. The

sharpness of the curve is selected using the Q switch to a Q of either 1

(wide band) or 2.4 (narrow band). Use wide band when you want to add

presence or warmth to the sound. Use narrow band to control problem

frequencies for example when notching out acoustic resonances.

(

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath GL 4000 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info