Bedienungsanleitung Allen-Heath MixWizard WZ3-16 (Seite 14 von 34) (Englisch)

541373

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

14 WZ

16:2 and 12:2 User Guide

L, R, M OUT The main console mix outputs are on balanced XLR.

These produce +4dBu when the meters read ‘0’. The M output can be

switched to provide a mono sum of the post-fade L and R signals, or the

AUX6 output.

The L and R outputs typically feed the house PA system in live sound

mixing, or a 2-track recorder in studio mixing. In mono mode, the M output

can provide an additional feed for a mono fill speaker or zone, or be used

as the main feed into a mono PA. Used with a mono PA the L and R mix

can provide a pair of subgroups, each with routing using the channel PAN

controls, inserts and faders. Configured to provide the AUX6 mix, the M

output is ideal for driving a sub bass speaker system when working with

an ‘aux fed subs’ PA. This provides the sub feed with its own per-channel

mix on balanced XLR and with dedicated fader alongside the main LR

faders for proper control of the house volume.

AB OUT A pair of impedance balanced TRS jacks can be configured to

provide an additional LR mix or engineers monitor send. These operate at

-2dBu line level. A front panel recessed ‘mode’ switch determines the

source to the AB output. This may be set to follow the console monitor

system and therefore feed an independent local stereo monitor or even

engineers wedge speaker. When set to follow the LR mix, the factory

default source is taken post LR fader. An internal option jumper is

available to change this to pre LR fader.

The unique AB output feature provides the MixWizard with a host of

possibilities… independent 2-track recording feed, broadcast feed, zone

and delay fill feeds, local monitor, engineers wedge monitor and more.

AUX OUT 1-6 Each aux send is available on an impedance balanced

TRS jack operating at -2dBu line level. An internal option is available to fit

a balanced line driver IC to provide an electronically balanced output

operating at +4dBu. Note that it is not usual to require this option as the

impedance balanced standard drive provides significant interference

rejection when feeding balanced equipment inputs.

The aux sends are typically used to feed stage monitors, effects devices

such as reverb and delay, and for special mix requirements.

MIDI IN A standard 5-pin DIN MIDI input socket is provided. This is

used with external MIDI equipment or a MIDI equipped PC to control the

built-in effects processor mute, presets and parameters. Free software

can be downloaded from the Allen & Heath web site for PC editing of the

parameters via MIDI.

FOOTSWITCH Mutes and unmutes the ST5 (ST1) effects return

channel, ideal for bypassing the effects between songs. Note that this

affects the internal processor and also any external effects device that

may be plugged in to these return inputs. Use a momentary or latching

footswitch as required. Shorting a TS or TRS jack tip to sleeve turns the

mute on.

SYS-LINK II OPTION A blank plate is fitted here as standard. The

Sys-Link II option kit is available from Allen & Heath. Refer to OPTIONS

later in this guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath MixWizard WZ3-16 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Allen-Heath MixWizard WZ3-16

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info