Bedienungsanleitung Allen-Heath MixWizard WZ4-16 (Seite 13 von 32) (Englisch)

541379

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Allen & Heath 13 WZ

16:2 and 12:2 User Guide

The Console connectors

MIC / LINE IN The channel PAD (LINE) switch selects either the MIC XLR or

the LINE TRS jack as the input source. The XLR is normalled through the TRS

jack. This means that the XLR can be used for microphone or line level signals

when nothing is plugged into the jack socket. Both inputs are balanced but can

be wired to work with unbalanced signals when required.

WARNING: Do not connect unbalanced sources or cables to

the XLR input when 48V phantom power is selected. To avoid loud

clicks always turn the channel off by pressing MUTE when switching

+48V on or off, and when plugging or unplugging cables.

STEREO LINE IN The WZ

12:2 has six stereo inputs comprising four chan-

nel inputs ST1,3 (unbalanced) and ST2,4 (balanced), and an additional two stereo

returns ST5 (balanced) and ST6 (unbalanced). The WZ

16:2 has two stereo

return inputs ST1 (balanced) and ST2 (unbalanced). All inputs use TRS jacks.

Unbalanced inputs automatically connect the TRS ring to ground for working

with balanced sources. The L input is normalled through the R input to accept

mono signals.

Note that the ST5 (WZ

12:2) or ST1 (WZ

16:2) stereo return input mixes

with the internal effects processor return. This means that an external effects

device fed from a different aux mix can mix with the internal processor to save

input channels. Alternatively, you could turn the internal unit off and use the ST5

(ST1) input with an external unit only if preferred.

INSERT A single 3-pole TRS jack carries the unbalanced insert signal. Tip =

send, Ring = return, Sleeve = common ground. The channel insert is post-HPF,

pre-EQ and operates at 0dBu. The LR mix insert is pre-fader and operates at -

2dBu. These should work fine with line level signal processing equipment such as

compressors, outboard EQ, delay units and so on. An example of a suitable ca-

ble is shown here:

DIRECT OUTPUT The mic/line channel direct output is available on an impedance

balanced TRS jack. It is a line level signal operating at 0dBu. The source is set using an

internal option jumper for each channel. The factory default setting is pre-fade (following

the pre/post-EQ setting). This may be changed to post-fade if preferred.

The direct outputs provide a useful source for multitrack recording. Many users prefer

pre-fade sends for this application so that the live show fader movements do not affect

the recording which can be mixed later. Another application is channel effects sends. For

example, a reverb unit may be dedicated to work with the lead vocalist channel only.

Using a post-fade direct output instead of an aux send frees up that aux mix for other

purposes.

MIC

LINE

TIPTIP +IN

RINGRING -IN

INPUT

+IN

- IN

MIX

ST1

L/M

EFFECT

OFF, 1-20

EXTERNAL

AUX5

AUX6

EFFECT

OFF, 1-20

INTERNAL FX

RETURN

INSERT

RETURN

SEND

RING

TIP

GROUND

RETURN

SEND

RETURN

OUT

SEND

INSERT

PROCESSOR

LINK RING TO SLEEVE TO UNBALANCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath MixWizard WZ4-16 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info