Bedienungsanleitung Allen-Heath PA-CP Series (Seite 10 von 36) (Englisch)

541349

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

10 PA-CP User Guide

Installing the Console

The PA Series is portable and designed for stand alone operation. The smaller PA12-CP model can

also be 19” rack mounted by replacing the trims with the rack ears provided. Either way, ensure

adequate ventilation around the unit and heed all warnings regarding mains power safety and earthing.

1 Carry Handle Metal handle for lifting and carrying the

console. The weight is centrally distributed. Lift the console by

holding the handle securely in the middle. To prevent damage

to the controls, carry it with the control surface away from you.

The console is necessarily heavy due to the high

power amplifiers built in. To avoid injury to yourself or

damage to the equipment always ensure you are correctly

positioned and grip securely when lifting, moving or

transporting the unit.

2 Feet Protective rubber feet are fitted to both the base and

the rear of the console so that it can be positioned for stand

alone operation or on the floor while it is being carried. This

avoids damage to the mounting surface and console parts.

3 Front and Side Trims The front armrest, carry handle and

side trims offer both protection and style to the console. They

can be easily removed for fitting the metal ears provided when

you want to permanently mount the console in a 19” rack or

plinth. This option only applies to the smaller PA12-CP model.

Instructions for fitting the rack ears is provided later in this user

guide. The console can be rack mounted in either of two

positions as described below.

4 Rack Position 1 Shows the ears fitted for top of rack

mounting. The controls are angled upwards above the rack for

easier access during operation. This position may also be

preferred when the console is mounted in a desk or other

furniture. 10U rack space is required. Allow additional space

for access to the rear panel connectors.

5 Rack Position 2 Shows the ears fitted for front of rack

mounting. The controls are flush with the rack and connectors

angled slightly back. 11U rack space is required. This allows

space for cables to be routed into the rack, and for the console

lamp to be accessed.

6 Ventilation and Cooling The console uses a twin fan

thermal management system to control the operating

temperature of the built-in 1kW power amplifiers. Air is drawn

in from the front and expelled from the rear. The fans run at

low speed when cool, medium speed on reaching 35 degrees

C, and fast speed at 50 degrees C. The unit shuts down safely

in thermal protect mode in the unlikely event that excessive

temperature is reached.

Do not obstruct the front or rear ventilation slots or

position the console where air flow required for ventilation

is impeded. The console must not be operated in any carry

or flight case that obstructs these slots. Ensure adequate

air flow when rack or plinth mounting the console.

7 Console Lamp Plug in a 4-pin XLR 12V gooseneck lamp

designed for this purpose. The right angled type is

recommended. A low or high intensity bulb up to 400mA

maximum can be used. Only one lamp may be connected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath PA-CP Series Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info