541352
48
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
Qu-16 User Guide 48 AP9031 iss.3
11.2 System Hard Reset
A power up reset is available if you need to fully reset
the Qu mixer settings and memories. This could be
done to clear the system out before sending the mixer
to a client, or if you suspect a system problem.
To reset mix parameters before starting a show or
sound check, use a Scene or the Reset Mix Setting
function described earlier in this guide.
Note – A hard reset clears all current settings, all
Scenes and all User Libraries.
First turn off the system including amplifiers and
powered speakers.
To hard reset the Qu mixer - Press and hold the
touch screen Reset and Setup keys together and then
power up the mixer. Keep the keys pressed for at least
3 seconds while the mixer boots. Release the keys.
The hard reset:
Resets the current settings as described for the
Reset Mix Settings button,
Resets non-scene parameters and user
preferences to a factory default,
Clears scene recall Safes,
Clears all memories including Scenes and User
Libraries
Resets the Network IP address and the touch
screen calibration
System hard reset:
Source Preamp, Gain 28dB, 48V off
ST1-3 trim 0dB
HPF out, 100Hz
PEQ and GEQ in, flat
Gates out, thres -36dB, depth 20dB
Comp out, thres 0dB, ratio 3.2:1
Delays 0ms
Mix source post-EQ
Sends to Mixes -Inf and pre-fade
Sends to FX -Inf and post-fade
Direct Out post-fade/mute, trim 0dB
Mutes off
Channel faders -Inf
FX return faders 0dB
FX send and Mix master faders -4dB
LR master fader -Inf
FX1 = Mix>Return, Reverb (EMT250)
FX2 = Mix>Return, Delay (Vocal)
FX 3 and 4 = unassigned
Mute Groups unassigned
AES, Alt Out patch LR post-fade
Qu-Drive stereo patch LR post-fade
USB patch CH1-16, ST1-3, LR
Talkback unassigned, HPF 120Hz
Custom Strip unassigned
SoftKeys = Mute Groups 1-4
Input PAFL = PFL, mix = AFL
PAFL additive mode off
Sel follow PAFL on, LR to PAFL on
PAFL trim 0dB, delay 0ms
Talkback mic gain 27dB
Sig Gen Pink Noise, unassigned
Clears all scene Safes
Clears all Scene memories
Clears all User Libraries
Resets Network address to DHCP
Resets touch screen calibration
Hold for 3 seconds
while powering up
the mixer
48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

allen-heath-qu-16

Suche zurücksetzen

  • Ich habe ein Problem wie kann ich q Drive aufnehmen und wieder play Eingereicht am 27-10-2019 14:48

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Allen-Heath QU-16 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info