Bedienungsanleitung Alpina A 455 (Seite 37 von 460) (Alle Sprachen)

608382

Zoom out

Zoom in

Vorherige Seite

1/460

Nächste Seite

This product has accordingly been designed with

a ventilation hatch on the right side of the surface

of the cylinder cover to allow warm air to be sup-

plied to the engine and to thereby prevent icing

from occurring.

Under normal circumstances the product should be

used in the normal operating mode, i.e., in the

mode which it is set at the time of shipment. How-

ever when the possibility exists that icing may oc-

cur, the unit should be set to operate in the anti-

freeze mode before use.

To switch from “Normal” mode to “Anti-freeze”

mode (and vice versa) (Fig. 11):

1. Switch the engine off.

2. Remove the air filter cover (1) and the air filter

(2).

3. Remove the choke (3) from the cylinder cover

(4).

4. Unscrew the screws (5) which secure the cylin-

der cover in place (three screws inside and one

outside) and remove the cylinder cover.

5. Use your fingers to press the anti-freeze cap (6)

on the right side of the cylinder cover and slide

it out from its seat.

6. Turn the anti-freeze cap (6) so that the "SNOW"

symbol is facing upwards and then replace the

cap.

7. Replace the cylinder cover and all the other

parts in their original position.

If the machine is used in anti-

freeze mode at higher temperatures, this may

cause difficulties when starting the engine and dur-

ing use due to the incorrect engine speed. Always

check that the machine is switched to normal mode

(with the "SUN" symbol facing upwards) if there is

no danger of ice forming.

NOTE

The chain speed is regulated by the throttle trigger

(1) on the rear handgrip (2).

The throttle trigger only works if the lockout (3) is

pressed at the same time.

The movement is transmitted from the engine to the

chain by a centrifugal mass clutch that prevents the

chain from moving when the engine is running at

minimum speed.

Do not use the machine if

the chain moves when the engine is running

idle; in this case, contact your dealer.

The correct running speed will be achieved by

pressing the throttle trigger (1) as far as possible.

Avoid using the engine at full

power for the first 6-8 working hours.

STOPPING THE ENGINE (Fig. 10)

To stop the engine:

– Release the throttle trigger (1) and allow the en-

gine to run idle for a few seconds.

– Set the switch (4) to «STOP».

When you have reduced

speed to a minimum, it may take a few sec-

onds for the chain to stop.

If the machine does not turn

off, pull the starter to flood and stop the engine and

immediately contact the dealer to find the cause of

the problem and request necessary repairs.

USING THE ANTI-FREEZE DEVICE

(excluding C 46 - XC 246 - C 50 - CP 45

- A 455 - MC 846 models) (Fig. 11)

Operating chain saws in temperatures of 0 – 5°C at

times of high humidity may result in ice forming

within the carburetor, and this in turn may cause the

output power of the engine to be reduced or for the

engine to fail to operate smoothly.

IMPORTANT

WARNING!

IMPORTANT

WARNING!

HOW TO START - USE – STOP THE ENGINE 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina A 455 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info