731914
9
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
EN
IDENTIFICATION OF MAIN COMPONENTS / SYMBOLS 3
[1]
Notice:
The vibration value indicated was determined with a standardized tool and can be used to make comparisons with other electric equipment
as well as temporary estimates of the load through the vibrations.
WARNING!
The vibration value may vary according to the usage of the machine and its tted equipment, and be higher than the one indicated. Safety
measures must be established to protect the user and must be based on the load estimate generated by the vibrations in real usage conditions.
In this regard, all the operational cycle phases must be taken into consideration, such as switching o or idle running.
The noise level may vary according to machine usage if working or running idle.
Maximum noise and vibration levels [1]
T 1.0 EJ
Sound pressure level
– Measurement uncertainty
dB(A)
dB(A)
79.3
3
Measured acoustic power level
– Measurement uncertainty
dB(A)
dB(A)
88,2
3
Guaranteed sound power level
dB(A) 96
Vibration level
– Measurement uncertainty
m/s
2
m/s
2
2.5
1.5
TECHNICAL DATA
T 1.0 EJ
Power supply voltage
V~ 230
Power supply frequency
Hz 50
Engine Power
W 1000
Cutting width
cm 37
Mass
kg 4,70
No-load Speed
min
-1
7000
Maximum engine and tool rotation speed
r.p.m 7000
2. SYMBOLS
1) Warning! Danger. The failure to use this ma-chine cor-
rectly can be hazardous for oneself andothers.
2) Read the instruction manual before
using themachine.
3) If you are using the machine every day
in normal conditions, you can be ex-
posed to a noise level of 85 dB(A) or
higher. Wear earmus or ear-plugs, eye
protection and a protective helmet.
4) Danger of ying objects! Keep any pe-
ople orpets at least 15 m away when
using the machine!
5) Disconnect the plug from the mains be-
fore commencing maintenance work or
if the power cord is damaged.
6) Do not leave the machine in the rain (or
in damp conditions).
7) Only one cutting line head can be used
on thismachine.
8) Do not use pointed, rigid or metal bla-
des orcircular saw blades.
9) Keep bystanders away.
10) Cutting device rotation direction.
11) Acoustic output level LWA.
2
1 2 3 4
5 6 7
8
9 10 11
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alpina ABR 1.0 EJ wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info