Bedienungsanleitung Alpina ACS 2.0 ET (Seite 15 von 23) (Alle Sprachen)

732013

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

1. CHECKS DURING WORK

• Checking the chain tension

The chain tends to stretch gradually as you work,

so you need to check its tension frequently.

IMPORTANT

During the rst period of use

(or after replacing the chain), it must be checked

more frequently due to settling of the chain.

WARNING! Never work with the chain

loose, as it can be hazardous if the chain slips

out of its guides.

To adjust the chain tension, follow the instructions

in Chapter 5.2.

• Checking the oil delivery

IMPORTANT

Never use the machine with-

out lubrication! You can check the oil level in the

tank through the transparent gauge. Make sure

you ll up the oil tank every time you use the ma

chine.

WARNING! Make sure the bar and the

chain are in place when you check the oil de-

livery.

Start the engine and check if the chain oil is de li -

vered as shown in the gure (Fig. 13).

• Shutdown whilst working (Only for

C 2.2 E/ET – SE 2216 / 2216 Q - A 220 EQ)

Your chain saw is designed with an overload

protection with circuit breaker. If the chain saw is

clogged (e.g. blocking of the cutting means, chain

teeth jammed, overload cutting) during the cutting

operation, the overload circuit breaker will cut the

mains power supply automatically to protect your

chain saw.

IMPORTANT

The circuit breaker will be

activated when the cutting current is over 35-40A,

and it can be reset manually by pressing the reset

button (1.15) 30 seconds after it has cooled com-

pletely.

2. DIRECTIONS FOR USE AND CUTTING

TECHNIQUES

Before felling or delimbing for the rst time, prac-

tise sawing logs on the ground or on trestles, so

that you can get familiar with the machine and the

most suitable sawing techniques.

WARNING! Always hold the machine

with both hands when sawing.

WARNING! Stop the engine im me dia

tely if the chain stops during sawing. Be wa re

of kickback, which can occur if the bar con-

tacts an obstacle.

• Felling a tree

– When bucking and felling operations are being

performed by two or more persons at the sa me

time, the felling operations should be separated

from the bucking operation by a distance of at

least twice the height of the tree being felled.

Trees should not be felled in a man ner that

would endanger any person, stri ke any utility

line or cause any property damage. If the tree

does make contact with any u ti lity line, the com-

pany should be notied im mediately.

– The chain saw operator should keep on the up-

hill side of the terrain as the tree is likely to roll

or slide downhill after it is felled.

– An escape path should be planned and clea-

red as necessary before cuts are started. The

e scape path should extend back and diagonally

to the rear of the expected line of fall as illus-

trated in Figure 15.

– Before felling is started, consider the natural

lean of the tree, the location of larger branches

and the wind direction to judge which way the

tree will fall.

– Remove dirt, stones, loose bark, nails, staples

and wire from the tree.

• Notching undercut

Make the notch 1/3 the diameter of the tree, per-

pendicular to the direction of falls as illustrated in

Figure 16.

Make the lower horizontal notching cut rst.

his will help to avoid pinching either the saw chain

or the guide bar when the second notch is being

made.

10 USING THE MACHINE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina ACS 2.0 ET Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info