Bedienungsanleitung Alpina AR-2 400 (Seite 21 von 32) (Englisch)

516562

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

User’s manual

REMOTE CONTROL: (only for some versions, see “Technical Speciﬁ cations).

See the instructions on the remote control / console for the pairing procedure.

SOUND: Allows disabling the acoustic signal when the robot is in the charging station.

BACK TO RECHARGE: Allows selecting the method for the robot’s return to the charging

station.

1. “Follow wire”. The robot returns to the charging station by positioning the wheels on

either side of the perimeter wire.

2. “V-METER”. The robot runs along the perimeter wire at an indicative distance ranging

from a few centimetres to one meter (3.2 '), touching it every now and again in the

curved sections until it recognises the “Recall” to the charging station. Refer to the

“Installation” chapter.

DATE: Function for setting the date.

TIME: Function for setting solar or daylight saving time.

ENTER

DATE DD/MM/YY

MON 00 / 00 / 00

WORK SCHEDULES – PROGRAMMING MODE

WEEK: function for programming the operating days of the robot during the week. The

cursor automatically positions itself under the letter “M” (Monday).

Setting all the days at “1111111” means that the robot will work every day. Setting “0000000”

means that the robot will not work on any day of the week.

Value 1 : Robot’s work day.

Value 0 : Robot’s rest day.

Important

To get the best out of the robot, it is recommended to program the robot

to work every day.

ENTER

WEEK

MTWTFSS

MON 1111111

WORK SCHEDULE 1: Function for setting the ﬁ rst time of the robot’s working day.

The cursor automatically positions itself in the area under the ﬁ rst time (e.g. 10:00am to

1:00pm). Set the time for the start and end of the work.

Setting the time at “00:00 – 00:00” means that the robot will not work during Work Schedule

1. Once entered. If the entered time is wrong such as if the time overlaps with the working

time 2 or if the starting time is after the end time, the robot beeps and resets the set value.

WORK SCHEDULE 2: Function for setting the second time of the robot’s working day.

Important

If it is necessary to set secondary areas, then it is preferable to program

both work schedules in order to increase the mowing frequency of the

area.

ENTER

WORKING TIME

00 : 00 - 00 : 00

The setting of the time is essential for the robot’s proper functioning. Many parameters inﬂ uence the setting of the work schedules, such as the

number of secondary areas, the number and the power of batteries of the robot, complexity of the lawn, type of grass, etc. Generally, the working

hours must be increased slightly when mowing gardens with secondary areas, with lots of obstacles and complicated areas. Below is a table with

the indicative times for conﬁ guring the robot on ﬁ rst use.

NB. Set all the weekdays at “1” – “Work Days.”

Model m² (ft²) Time 1 Time 2

075BA0 150 (1615) 11:00 11:40 15:00 15:30

075BA0 300 (3230) 11:00 17:00

075BA0 400 (4304) 11:00 19:00

075DE0 150 (1615) 11:00 11:40

075DE0 300 (3230) 11:00 11:40 15:00 15:40

075DE0 400 (4304) 10:00 16:00

075DE0 600 (6460) 10:00 19:00

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina AR-2 400 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpina AR-2 400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info