Bedienungsanleitung Alpina C 2.0 ET (Seite 13 von 23) (Alle Sprachen)

732007

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

8 PREPARING TO WORK / STARTING - STOPPING THE ENGINE

3. Press the safety button (6) and then the switch

(7).

NOTE

When you release the

switch, the safety button is also released and the

engine stops.

WARNING! The chain may take one

second to come to a stop after the engine is

switched o.

STOPPING THE ENGINE

To stop the engine:

– Release the switch (7).

– FIRST unplug the extension lead (3) from the

mains socket (4) and THEN disconnect the

power cable (2) of the machine from the exten-

sion lead (3).

STARTING THE ENGINE (Fig. 12)

Before starting the engine:

– Fasten the extension lead (1) to the cable clamp

on the rear handgrip.

– FIRST connect the power cable plug (2) to the

extension lead (3) and THEN plug the extension

lead into the mains socket (4).

– Take o the bar cover.

– Make sure the bar is not touching the ground or

any other object

To start the engine (Fig. 12):

1. Disengage the chain brake (5) by pulling the

front hand guard towards the front handgrip.

2. Hold the chain-saw rmly with both hands.

6. HOW TO START - STOP THE ENGINE

WARNING! Do not use the machine if

the chain brake does not function correctly

and have it inspected by your dealer.

4. CHAIN LUBRICANT

IMPORTANT

Only use chain-saw oil or

adhe sive oil for chain-saws. Do not use oil con-

taining impurities, to avoid clogging the tank lter

and permanently damaging the oiler.

IMPORTANT

The chain lubricating oil is

bio-degradable. The use of mineral oil or engine oil

can have a serious impact on the environment.

It is essential that you use good quality oil to lubri-

cate the cutting parts eectively.

Used or poor quality oil does not guarantee good

lubrication and reduces the duration of the chain

and bar.

IMPORTANT

Before each machine use,

the oil level should be checked and topped up to

1 cm from the rim of the ller. The oil level must not

drop below the «MIN» level mark.

5. ELECTRICAL CONNECTIONS

DANGER! Electricity and moisture

are not compatible.

– Always handle and connect electric cables

in dry conditions.

– Keep electric sockets or cables away from

wet and damp areas (e.g. puddles or wet

ground).

The quality of the extension leads must be no less

than H07RN-F or H07VV-F, with a minimum sec-

tion of 1.5 mm

and a recommended maximum

length of 30 m.

To avoid overheating, do not keep the extension

lead rolled up during use.

DANGER! The permanent connec-

tion of any electrical equipment to the mains

of a building must be installed by a qualied

electrician in conformity with the regulations

in force. Incorrect wiring can cause serious

injury and even death.

DANGER! Supply power to the ma-

chine using a dierential switch (RCD  Resid-

ual Current Device) with a tripping current of

max. 30 mA.

IMPORTANT

To prevent power supply ou-

tages:

– make sure that the electric system’s overall ca-

pacity is adequate;

– connect the machine to a mains socket with suf-

cient amperage;

– avoid simultaneous use of other electrical ap-

pliances with high power consumption.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina C 2.0 ET Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info