Bedienungsanleitung Alpina TB 250 D (Seite 18 von 28) (Alle Sprachen)

731981

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

– Wash the lter element (2) with soap and wa ter.

Do not use petrol or other solvents.

– Leave the lter to dry in the open air.

– Fit the lter element (2) and the cover (1) back

on, tightening the knob (3) again.

CHECKING THE SPARK PLUG (Fig. 17)

Periodically remove and clean the spark plug us-

ing a metal brush to get rid of any deposits.

Check and reset the correct distance between the

electrodes.

Replace the spark plug and fasten it rmly using

the supplied wrench.

The spark plug must be replaced with one with

the same characteristics whenever the electrodes

have burnt or the insulation has worn, and in any

case every 100 working hours.

TUNING THE CARBURETTOR

The carburettor is tuned by the manufacturer to

achieve maximum performance in all situations,

with a minimum emission of toxic gas in compli-

ance with the regulations in force.

In the case of poor performance contact your

Dealer for a check of the carburetion and engine.

• Tuning minimum speed

WARNING!

The cutting device must

not move when the engine is running idle. If

the cutting device moves when the engine is

running idle, contact your dealer to correctly

regulate the engine.

ANGLE TRANSMISSION (Fig. 18)

Lubricate with lithium-based grease.

Remove the screw (1) and put in the grease, turn-

ing the shaft manually until grease emerges, then

replace the screw (1).

SHARPENING THE 3 POINT BLADE (Fig. 19)

WARNING!

Use protective gloves. If

sharpening is done without removing the

blade, disconnect the spark plug cap.

Correct maintenance is essential to maintain the

original eciency and safety of the machine over

time.

WARNING!

During maintenance ope-

ra tions:

– Remove the spark plug cap.

– Wait until the engine is suciently cold.

– Use protective gloves when handling the

blades.

– Keep the blade protection device on, except

when intervening directly on the blade.

– Never dispose of oils, fuel or other pollut-

ing materials in unauthorised places.

CYLINDER AND SILENCER

To reduce re risks, periodically clean the cylinder

aps with compressed air and clear the silencer

area to get rid of sawdust, branches, leaves or

other debris.

STARTING SYSTEM

To avoid overheating and damage to the engine,

always keep the cooling air vents clean and free

of sawdust and debris.

The starter rope must be replaced as soon as it

shows signs of wear.

NUTS AND SCREWS

Periodically check that all the nuts and screws are

securely tightened and the handgrips are tightly

fastened.

CLEANING THE AIR FILTER (Fig. 16)

IMPORTANT

Cleaning the air filter is

essential to guarantee the eciency and du-

ration of the machine. Do not work with a

damaged filter or without a filter, as this

could permanently damage the engine.

It must be cleaned after every 8-10 working hours.

Clean the lter as follows:

– Loosen the knob (3), remove the cover (1) and

the lter element (2).

MAINTENANCE AND STORAGE

8. MAINTENANCE AND STORAGE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpina TB 250 D Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info