Bedienungsanleitung Alpine CDA-118M (Seite 11 von 51) (Englisch, Französisch, Spanisch)

466971

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

9-EN

Press TUNE/A.ME to select the tuning mode.

DX SEEK (Distance mode) SEEK (Local mode)

(Blank) (Manual mode) DX SEEK (Distance mode)

• The initial mode is Distance mode.

Distance mode:

Both strong and weak stations will be automatically tuned in

(Automatic Seek Tuning).

Local mode:

Only strong stations will be automatically tuned in (Automatic

Seek Tuning).

Manual mode:

The frequency is manually tuned in steps (Manual tuning).

Press or to tune in the desired station.

Holding down or will change the frequency

continuously.

• If DIGITAL SEEK is set to ON, the SEEK UP/DOWN functions only

stop on digital station frequencies while receiving an HD Radio

signal. Refer to

“Digital Seek On/Off Setting” (page 27).

Presetting Stations Manually

Select the radio band and tune in a desired radio

station you wish to store in the preset memory.

Press and hold PRESET for at least 2 seconds.

The Preset screen is displayed.

Turn the Rotary encoder to select the preset

number.

Press and hold / ENTER for at least 2 seconds.

The selected station is stored.

The display shows the band, preset number and station

frequency memorized.

• A total of 18 stations can be stored in the preset memory (12-FM,

6-AM).

• If you store a station in a preset memory which already has a station,

the current station will be cleared and replaced with the new station.

Presetting Stations Automatically

Press TUNER/SOURCE repeatedly until the desired

radio band is displayed.

Press and hold TUNE/A.ME for at least 2 seconds.

The tuner automatically seeks and stores the strongest

available stations in the selected band (12-FM, 6-AM). They

will be stored to preset memory in order of signal strength

(For FM P1 to P12, for AM P1 to P6).

When the automatic memory has been completed, the tuner

goes to the station stored in preset location No.1.

• If no stations are stored, the tuner will return to the original station

you were listening to before the auto memory procedure began.

Tuning to Preset Stations

Press TUNER/SOURCE repeatedly until the desired

band is displayed.

Press and hold PRESET for at least 2 seconds.

The Preset screen is displayed.

Turn the Rotary encoder to select a radio station.

Press /ENTER.

The display shows the band, preset number and frequency

of the station selected.

• You can also call up the desired preset memory by pressing PRESET

repeatedly.

Frequency Search Function

You can search for a radio station by its frequency.

Press /ENTER in Radio mode to activate

Frequency search mode.

Turn the Rotary encoder to select the desired

frequency.

Press /ENTER to receive the selected frequency.

* Operation is not required during HD Radio reception.

• Press in the search mode to cancel. Or, the search mode will be

canceled if no operation is performed for 10 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDA-118M Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info