466971
23
Zoom out
Zoom in
Vorherige Seite
1/51
Nächste Seite
21-EN
Turning Subwoofer ON/OFF
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 20).
For this unit, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold AUDIO for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the Rotary encoder to select the SUBW
mode, and then press
/ENTER.
SUBW SUBW SYSTEM*
1
BASS TREBLE
HPF SUBW
*
1
Displayed only when subwoofer is ON.
3
Turn the Rotary encoder to select SUBW ON/OFF,
and then press
/ ENTER.
ON OFF
4
Press to return to normal mode.
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
If is pressed during setting, the unit returns to the previous item.
Setting the Subwoofer System
When the subwoofer is on, you can select either SYS 1 or SYS 2 for the
desired subwoofer effect.
For this unit, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold AUDIO for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the Rotary encoder to select the SUBW
SYSTEM mode, and then press
/ ENTER.
SUBW SUBW SYSTEM*
1
BASS TREBLE
HPF SUBW
*
1
Displayed only when subwoofer is ON.
3
Turn the Rotary encoder to select the SUBW SYS 1
or SUBW SYS 2, and then press
/ ENTER.
SYS 1 SYS 2
4
Press to return to normal mode.
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
If is pressed during setting, the unit returns to the previous item.
This function is inoperable when Subwoofer is set to OFF.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
For this unit, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold AUDIO for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the Rotary encoder to select the BASS
Adjustment mode, and then press
/ENTER.
SUBW SUBW SYSTEM*
1
BASS TREBLE
HPF SUBW
*
1
Displayed only when subwoofer is ON.
3
-1*
2
Turn the Rotary encoder to select the desired
bass level (–7~+7), and then press
/ ENTER.
You can emphasize or weaken the bass level.
3
-2 Turn the Rotary encoder to select the desired bass
bandwidth, and then press
/ ENTER.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
SYS 1 : Subwoofer level changes according to the main
volume setting.
SYS 2 : Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Bass Level
Setting the Bass Bandwidth
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alpine CDA-118M wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info