Bedienungsanleitung Alpine cda 7878 r (Seite 19 von 48) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Schwedisch)

168577

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

17-EN

Receiving Traffic Information

1 Press the T.INFO button to activate the Traffic

Information mode.

To cancel the Traffic information mode, press the

T.INFO button again.

2 Press the g DN or f UP button to select

your desired traffic information station. When a

traffic information station is tuned in, the TP

indicator lights up.

Traffic information is heard only when it is being

broadcast. If traffic information is not being

broadcast, the unit is set in the standby mode.

When a traffic information broadcast begins, the

unit automatically receives it and the display

shows "TRAFFIC-INFO" for 5 seconds, then

returns to the previous display.

When traffic information broadcast is over, the

unit will automatically set in the standby mode.

NOTES

• If the traffic information broadcast signal falls below a

certain level, the unit remains in the receiving mode

for 1 minute. If the signal remains below a certain

level for over 1 minute, the "T.INFO" indicator blinks.

• If you do not want to listen to the traffic information

being received, lightly press the T.INFO button to skip

that traffic information message. The T.INFO mode

will remain in the ON position to receive the next

traffic information message.

• If the volume level is changed while receiving traffic

information, the changed volume level will be

memorized. When traffic information is received next

time, the volume level will be automatically adjusted

to the level memorized.

• In the T.INFO mode, the SEEK tuning selects only the

TP stations.

PTY (Programme Type) Tuning

1 Press the "F" button. The indicator will

illuminate.

2 Press the PTY button to activate the PTY mode.

The Programme Type of the station being

currently received will be displayed for 5

seconds.

If there is no receivable PTY broadcast, "NO

PTY" will be displayed for 5 seconds.

NOTE

If no buttons are pressed within 5 seconds after pressing

the PTY button, the PTY mode will be automatically

cancelled.

3 Press the g DN and f UP buttons within 5

seconds after activating the PTY mode to

choose the desired programme type while the

PTY (programme type) is being displayed. Each

press scrolls the programme type by one.

→ LIGHT M ↔ CLASSICS ↔ OTHER M ←

4 Press the PTY button within 5 seconds after

selecting the programme type to start searching

for a station in the selected programme type.

The chosen programme type indicator blinks

during searching and lights when a station is

found.

If no station is found, "NO PTY" will be displayed

for 5 seconds.

5 Press the "F" button to activate the normal mode.

The

indicator will turn off.

NOTE

Operate the unit while the indicator is

illuminated.

If no buttons are pressed within 5 seconds, the

indicator will turn off.

PI SEEK Setting

1 Press and hold the SETUP button for at least 2

seconds.

2 Press the f UP button repeatedly to select

"PI SEEK."

3 Press the TUNE button to toggle the mode

between "PI SEEK ON" and "PI SEEK OFF."

4 Press the SETUP button to set the selected

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine cda 7878 r Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info