Bedienungsanleitung Alpine CDE-112Ri (Seite 16 von 37) (Englisch)

471315

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

14-EN

Press and hold ESC for at least 2 seconds to return to

normal mode.

Notes

• If no operation is performed for 15 seconds, the unit will return to

normal mode automatically.

• The function is inoperable when DEFEAT is set to ON.

You can change the Bass Frequency emphasis to create your own tonal

preference.

 Setting item: BASS

Setting the Bass Centre Frequency

Press BANDTA to select the desired bass centre

frequency.

80 Hz  100 Hz  200 Hz  60 Hz  80 Hz

Emphasises the displayed bass frequency ranges.

Setting the Bass Bandwidth

Press SOURCE to select the desired bass bandwidth.

Changes the boosted bass bandwidth to wide or narrow. A

wider setting will boost a wide range of frequencies above and

below the centre frequency. A narrower setting will boost only

frequencies near the centre frequency.

Setting the Bass Level

Turn the Rotary encoder to select the desired bass level

(-7~+7)

You can emphasise or weaken the bass level.

* The adjustment can also be made by pressing Rotary encoder.

Refer to “Adjusting Subwoofer Level/Bass Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Defeat” on page 13.

Note

• The bass level settings will be individually memorized for each source

(FM, MW (LW), CD, etc.) until the setting is changed. The bass

frequency and bass bandwidth settings adjusted for one source are

effective for all other sources (FM, MW (LW), CD, etc.).

You can change the Treble Frequency emphasis to create your own tonal

preference.

 Setting item: TREBLE

Setting the Treble Centre Frequency

Press BANDTA to select the desired treble centre

frequency.

10.0 kHz  12.5 kHz  15.0 kHz  17.5 kHz  10.0 kHz

Emphasises the displayed treble frequency ranges.

Setting the Treble Level

Turn the Rotary encoder to select the desired treble level

(-7~+7)

You can emphasise the treble level.

* The adjustment can also be made by pressing Rotary encoder.

Refer to “Adjusting Subwoofer Level/Bass Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Defeat” on page 13.

Note

• The treble level settings will be individually memorized for each source

(FM, MW (LW), CD, etc.) until the setting is changed. The Treble

frequency settings adjusted for one source are effective for all other

sources (FM, MW (LW), CD, etc.).

The High Pass Filter on this unit can be adjusted to suit your personal

taste.

 Setting item: HPF

Turn the Rotary encoder to select the desired HPF

frequency.

OFF  60 Hz  80 Hz  100 Hz

All frequencies above the selected cutoff are output.

Turning Loudness On/Off

Loudness introduces a special low-and high-frequency emphasis at low

listening levels. This compensates for the ear’s decreased sensitivity to

bass and treble sound.

Press and hold Rotary encoder (LOUD) for at least

2 seconds to activate or deactivate the loudness mode.

Note

• The function is inoperable when DEFEAT is set to ON.

Setting the Bass Control

Setting the Treble Control

(Narrow)

(Wide)

Adjusting the High Pass Filter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-112Ri Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-112Ri

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info