Bedienungsanleitung Alpine CDE-112Ri (Seite 35 von 37) (Englisch)

471315

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

33-EN

 Full Speed Connector

Control iPhone/iPod signals.

Connect this to an iPhone/iPod by using FULL SPEED Connection

Cable (KCE-433iV) (sold separately for CDE-111R/CDE-111RM/

CDE-113BT) or to an external device (such as a portable player) by

using conversion cable (KCE-237B) for building up the AUX IN (sold

separately).

Note

• Refer to “Setting the AUX+ SETUP Mode” on page 19.

AUX+ ON :

When the external device is connected.

AUX+ OFF :

When an iPhone/iPod is connected.

You can also connect this to an optional BLUETOOTH INTERFACE

(KCE-400BT) (CDE-111R/CDE-111RM/CDE-112Ri only). To use a

hands-free mobile phone, an optional BLUETOOTH INTERFACE

(KCE-400BT) connection is required. For details on connection, refer

to the Owner’s Manual of the BLUETOOTH INTERFACE (KCE-400BT).

 Antenna Receptacle

 Audio Interrupt In Lead (Pink/Black)

Connect this lead to the Audio Interface output of a cellular phone

which provides ground shorting when a call is received.

 Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your amplifier or

signal processor.

 Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle’s fuse box or

another unused power source which provides (+) 12V only when the

ignition is turned on or in the accessory position.

 Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure

the connection is made to bare metal and is securely fastened using

the sheet metal screw provided.

 Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna, if

applicable.

Note

• This lead should be used only for controlling the vehicle’s power

antenna. Do not use this lead to turn on an amplifier or a signal

processor, etc.

 Dimmer Lead (Orange) (CDE-112Ri/CDE-113BT/ CDE-114BTi

only)

This lead may be connected to the vehicle’s instrument cluster

illumination lead. This will enable the vehicle’s dimmer control to dim

the backlighting of the unit.

 Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle’s battery.

 ISO Power Supply Connector

 ISO Connector (Speaker Output)

 Left Rear (+) Speaker Output Lead (Green)

 Left Rear (−) Speaker Output Lead (Green/Black)

 Left Front (+) Speaker Output Lead (White)

 Left Front (−) Speaker Output Lead (White/Black)

 Right Front (−) Speaker Output Lead (Grey/Black)

 Right Front (+) Speaker Output Lead (Grey)

 Right Rear (−) Speaker Output Lead (Violet/Black)

 Right Rear (+) Speaker Output Lead (Violet)

 Steering Remote Control Interface Connector

To steering remote control interface box.

You can operate this unit from the vehicle’s control unit when an

Alpine Steering Remote Control Interface Box (optional) is

connected. For details, contact your Alpine dealer.

 MIC Input Connector (CDE-113BT/CDE-114BTi only)

To M icrophone.

 Fuse Holder (10A)

 Front Output RCA Connectors (CDE-112Ri/CDE-113BT/

CDE-114BTi only)

RED is right and WHITE is left.

 Rear/Subwoofer Output RCA Connectors (CDE-112Ri/

CDE-113BT/CDE-114BTi only)

Front/Subwoofer Output RCA Connectors (CDE-111R/CDE-111RM

only)

RED is right and WHITE is left.

 Power Supply Connector

 RCA Extension Cable (sold separately)

 FULL SPEED Connection Cable (KCE-433iV) (sold separately

for CDE-111R/CDE-111RM/CDE-113BT)

 KCE-400BT Connection Cable (Included with KCE-400BT)

 ISO/JASO Antenna Adaptor (sold separately)

An ISO/JASO antenna adapter may be required, depending on the

vehicle.

 Front AUX Input Terminal (CDE-112Ri/CDE-113BT/

CDE-114BTi only)

This terminal allows for input of audio from an external device (such

as a portable player), using a commercially-available converter cable.

 USB Terminal

Connect this to a USB Memory (sold separately).

To prevent external noise from entering the audio system.

• Locate the unit and route the leads at least 10 cm away from the

car harness.

• Keep the battery power leads as far away from other leads as

possible.

• Connect the ground lead securely to a bare metal spot (remove

any paint, dirt or grease if necessary) of the car chassis.

• If you add an optional noise suppressor, connect it as far away

from the unit as possible. Your Alpine dealer carries various

noise suppressors, contact them for further information.

• Your Alpine dealer knows best about noise prevention

measures so consult your dealer for further information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-112Ri Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-112Ri

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info