Bedienungsanleitung Alpine CDE-113BT (Seite 8 von 37) (Englisch)

471314

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

6-EN

* The illustrator is for CDE-114BTi.

Accessory List

• Head Unit ..................................................................................1

• Power Cable ..............................................................................1

• FULL SPEED Connection Cable

(CDE-112Ri/CDE-114BTi only) .................................................1

• Microphone (4 m) (CDE-113BT/CDE-114BTi only) .................1

• Mounting Sleeve ......................................................................1

• Carrying Case............................................................................1

• Rubber Cap ...............................................................................1

• Hex Bolt.....................................................................................1

• Screw (M5 × 8) ..........................................................................4

• Owner’s Manual..................................................................1 set

Turning Power On and Off

Press SOURCE to turn on the unit.

Note

• The unit can be turned on by pressing any other button except  and

 (Release).

Press and hold SOURCE for at least 2 seconds to turn

off the unit.

Note

• The first time power is turned on, the volume will start from level 12.

Source Selection

Press SOURCE to change the source.

TUNER  DISC  USB AUDIO  iPod

/AUX+

 BT AUDIO



AUX

 TUNER

*1 Only when the iPhone/iPod is connected and AUX+ SETUP is

set to OFF, refer to “Setting the AUX+ SETUP Mode” on

page 19.

*2 Displayed only when AUX+ SETUP is set to ON, refer to

“Setting the AUX+ SETUP Mode” on page 19.

*3 Only for CDE-111R/CDE-111RM/CDE-112Ri and BT IN is set

to BT ADAPTER. Refer to “BLUETOOTH Setting” on page 17.

*4 Refer to “Using the Front AUX Input Terminal (CDE-112Ri/

CDE-113BT/CDE-114BTi only)” on page 15.

Detaching and Attaching the Front Panel

Turn off the unit power.

Press  (Release) at the lower left side until the front

panel pops out.

Grasp the left side of the front panel and pull it out.

Notes

• The front panel may become hot in normal usage (especially the

connector terminals on the back of the front panel). This is not a

malfunction.

• To protect the front panel, place it in the supplied carrying case.

• When detaching the front panel, do not apply excessive force as it may

result in malfunction.

Insert the right side of the front panel into the main unit.

Align the groove on the front panel with the projections

on the main unit.

Push the left side of the front panel until it locks firmly into

the main unit.

Notes

• Before attaching the front panel, make sure that there is no dirt or dust

on the connector terminals and no foreign object between the front

panel and the main unit.

• Attach the front panel carefully, holding the sides of the front panel to

avoid pushing buttons by mistake.

Initial System Start-Up

Be sure to press the RESET switch when using the unit for the first time,

after changing the car battery, etc.

Turn off the unit power.

Remove the detachable front panel.

Getting Started

SOURCE/

6/DIMMER

FUNC./SETUP



Rotary encoder

Detaching

Attaching

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-113BT Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-113BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info