Bedienungsanleitung Alpine CDE-125BT (Seite 14 von 35) (Englisch)

471377

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

15-EN

Adjusting Subwoofer Level/Bass Level/

Treble Level/Balance (Between Left and

Right)/Fader (Between Front and Rear)/

Defeat

Press Rotary encoder (AUDIO) repeatedly to choose the

desired mode.

Each press changes the mode as follows:

SUBWOOFER

 BASS LEVEL  TRE LEVEL  BALANCE  FA DER

 DEFEAT  VOLUME  SUBWOOFER

* When the subwoofer mode is set to OFF, its level cannot be

adjusted.

Note

• If no operation is performed for 5 seconds, the unit automatically

returns to normal mode.

Turn the Rotary encoder until the desired sound is

obtained in each mode.

By setting DEFEAT ON, previously adjusted settings of BASS

LEVEL and TRE LEVEL will return to the factory defaults.

Setting the Bass/Treble/High Pass Filter

Use steps 1 to 3 to select one of the setting modes to modify. See the

applicable section below for details about the selected setting item.

Press SOUND to select the desired Sound Setting

mode.

BASS  TREBLE  HPF  BASS

Turn the Rotary encoder or press BANDTA , SOURCE

etc., to change the setting.

Press and hold ESC for at least 2 seconds to return to

normal mode.

Notes

• If no operation is performed for 15 seconds, the unit will return to

normal mode automatically.

• The function is inoperable when DEFEAT is set to ON.

You can change the Bass Frequency emphasis to create your own tonal

preference.

 Setting item: BASS

Setting the Bass Centre Frequency

Press BANDTA to select the desired bass centre

frequency.

80 Hz  100 Hz  200 Hz  60 Hz  80 Hz

Emphasises the displayed bass frequency ranges.

Setting the Bass Bandwidth

Press SOURCE to select the desired bass bandwidth.

Changes the boosted bass bandwidth to wide or narrow. A

wider setting will boost a wide range of frequencies above and

below the centre frequency. A narrower setting will boost only

frequencies near the centre frequency.

Setting the Bass Level

Turn the Rotary encoder to select the desired bass level

(-7~+7)

You can emphasise or weaken the bass level.

* The adjustment can also be made by pressing Rotary encoder.

Refer to “Adjusting Subwoofer Level/Bass Level/Treble Level/

Balance (Between Left and Right)/Fader (Between Front and

Rear)/Defeat” on page 15.

Note

• The bass level settings will be individually memorized for each source

(FM, MW (LW), CD, etc.) until the setting is changed. The bass

frequency and bass bandwidth settings adjusted for one source are

effective for all other sources (FM, MW (LW), CD, etc.).

You can change the Treble Frequency emphasis to create your own tonal

preference.

 Setting item: TREBLE

Setting the Treble Centre Frequency

Press BANDTA to select the desired treble centre

frequency.

10.0 kHz  12.5 kHz  15.0 kHz  17.5 kHz  10.0 kHz

Emphasises the displayed treble frequency ranges.

Sound Setting

Subwoofer +0 ~ +15

Bass level -7 ~ +7

Treble level -7 ~ +7

Balance L15 ~ R15

Fader R15 ~ F15

Defeat ON/OFF

Volume 0 ~ 35

BAND/TA

/SOUND

SOURCE/



/ESC

Rotary encoder (AUDIO/LOUD)

Setting the Bass Control

Setting the Treble Control

(Narrow)

(Wide)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-125BT Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-125BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info