Bedienungsanleitung Alpine CDE-125BT (Seite 23 von 35) (Englisch)

471377

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

24-EN

Voice Dial Operation

You can call the telephone by performing voice operation.

Press and hold VOICE DIAL for at least 2 seconds.

The speak mode is activated, and “SPEAK” is displayed.

Say the telephone number, name you want to call into the

microphone.

Notes

• You can perform this operation only when a voice dial compatible

mobile phone is connected. If the mobile phone is not compatible with

the voice dial, “NO SUPPORT” is displayed for 2 seconds.

• The Voice Dial function performance depends on the recognition range

of the mobile phone and mounting location of the microphone. Please

pay attention when the microphone is mounted.

• Voice dial operation depends on the function of the mobile phone. For

details, refer to the Owner’s Manual of the mobile phone.

• If a called person that you say is not found, “NO CALL” is displayed for

2 seconds.

• If you place a call via voice dial, you cannot display a phone number or

name.

Adjusting the volume when receiving a Call

While calling, you can adjust the volume.

Turn the Rotary encoder to adjust the volume.

Note

• You may need to increase volume from your regular audio listening

source level. However, increasing the volume excessively may result in

feedback. If feedback is noticed as feedback is directly related to the

volume, turn down the volume as low as acceptable to eliminate it.

Positioning the microphone in a direction away from the main car

speakers (e.g. clipped on sun visor) may also reduce feedback at high

volume.

Call Switching Operation

While making a call, this function allows you to initiate the transfer of

the audio between the mobile phone and the speakers in the car.

While calling, press and hold ENT for at least

2 seconds to switch the call sound between the unit and

mobile phone.

Note

• Depending on the mobile phone, this operation may not be performed.

Playing MP3/WMA/AAC Files with the USB

Memory (optional)

If you connect a USB memory containing MP3/WMA/AAC, the

following table shows which type of files can be played on which models.

Press SOURCE to switch to the USB AUDIO mode.

To pause playback, press ENT.

Pressing ENT again will resume the playback.

Notes

• The root folder is displayed as “ROOT” in the Folder Name Search

mode.

• When a search is made in the USB mode, any song being played back

will be stopped.

• This unit plays back files in the USB Memory with the same controls

and modes as playback of CDs containing MP3/WMA/AAC. For

details, refer to “CD/MP3/WMA/AAC” on page 12.

• Before disconnecting USB Memory, be sure to change to another source

or set to pause.

• The playback time may not be correctly displayed when a VBR

(Variable Bit Rate) recorded file is played back.

USB Memory Connection (optional)

Open the cover of the USB Connection Terminal.

USB Memory (optional)

MP3 WMA AAC

CDE-126BT 

CDE-125BT 

Connect USB Memory

SOURCE/

/ENT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-125BT Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-125BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info