Bedienungsanleitung Alpine CDE-181RM (Seite 30 von 34) (Englisch)

536905

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30-EN

Installation and Connections

Before installing or connecting the unit, please read the following

and refer to “Operating Instructions” on page 5 for proper use.

WARNING

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or

product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may

result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY

TERMINAL.

Failure to do so may result in electric shock or injury due to

electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other

equipment. Doing so will exceed the current carrying capacity of

the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions

so as not to contact, damage or obstruct pipes, fuel lines, tanks or

electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO

MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other

safety-related system), or tanks should NEVER be used for

installations or ground connections. Using such parts could disable

control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF

CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult

a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE

OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER.

Doing so may obstruct forward vision or hamper movement etc.

and results in serious accident.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING

OBJECTS.

Arrange wiring and cables in compliance with the manual to

prevent obstructions when driving. Cables or wiring that obstruct

or hang up on places such as the steering wheel, shift lever, brake

pedals, etc. can be extremely hazardous.

CAUTION

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical

skill and experience. To ensure safety, always contact the dealer

where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than

designated parts may damage this unit internally or may not

securely install the unit in place. This may cause parts to become

loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP

METAL EDGE.

Route the cables and wiring away from moving parts (like the seat

rails) or sharp or pointed edges. This will prevent crimping and

damage to the wiring. If wiring passes through a hole in metal, use a

rubber grommet to prevent the wire’s insulation from being cut by

the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of

moisture or dust. Moisture or dust that penetrates into this unit may

result in product failure.

PRECAUTIONS

• Be sure to disconnect the cable from the (−) battery post before

installing your CDE-182R/CDE-181 Series/CDE-180 Series/

UTE-81R. This will reduce any chance of damage to the unit in case

of a short-circuit.

• Be sure to connect the colour coded leads according to the diagram.

Incorrect connections may cause the unit to malfunction or damage

to the vehicle’s electrical system.

• When making connections to the vehicle’s electrical system, be aware

of the factory installed components (e.g. on-board computer). Do not

tap into these leads to provide power for this unit. When connecting

the CDE-182R/CDE-181 Series/CDE-180 Series/UTE-81R to the

fuse box, make sure the fuse for the intended circuit of the

CDE-182R/CDE-181 Series/CDE-180 Series/UTE-81R has the

appropriate amperage. Failure to do so may result in damage to the

unit and/or the vehicle. When in doubt, consult your Alpine dealer.

• The CDE-182R/CDE-181 Series/CDE-180 Series/UTE-81R uses

female RCA-type jacks for connection to other units (e.g. amplifier)

having RCA connectors. You may need an adaptor to connect other

units. If so, please contact your authorized Alpine dealer for

assistance.

• Be sure to connect the speaker (−) leads to the speaker (−) terminal.

Never connect left and right channel speaker cables to each other or

to the vehicle body.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine CDE-181RM Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine CDE-181RM

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info