Bedienungsanleitung Alpine cdm 7859 rb (Seite 13 von 24) (Englisch)

168334

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

11-EN

Receiving RDS Regional (Local) Stations

1 Press and hold the SETUP button for at least 3

seconds to activate the setting mode.

2 Press the g DN or f UP button to select

the REG mode.

3 Press the BAND button to turn on or off the REG

(Regional) mode.

In the REG OFF mode, the unit automatically

keeps receiving the related local RDS station.

4 Press the SETUP button to deactivate the setting

mode.

Receiving Traffic Information

1 Press the T.INFO button repeatedly until the

T.INFO indicator appears in the display.

2 Press the g DN or f UP button to select

your desired traffic information station. When a

traffic information station is tuned in, the TP

indicator lights up.

Traffic information is heard only when it is being

broadcast. If traffic information is not being

broadcast, the unit is set in the standby mode.

When a traffic information broadcast begins, the

unit automatically receives it and the display

shows "TRF-INFO" for a few seconds and

returns to the PS display.

When the traffic information broadcast is over, the

unit will automatically set in the standby mode.

NOTES

• If the traffic information broadcast signal falls below a

certain level, the unit remains in the receiving mode

for 1 minute. If the signal remains below a certain

level for over 1 minute, the "T.INFO" indicator blinks.

• If you do not want to listen to the traffic information

being received, lightly press the T.INFO button to

skip that traffic information message. The T. INFO

mode will remain in the ON position to receive the

next traffic information message.

• If the volume level is changed while receiving traffic

information, the changed volume level will be

memorized. When traffic information is received next

time, the volume level will be automatically adjusted

to the level memorized.

PTY (Programme Type) Tuning

1 Press the F button so that the F (Function)

indicator lights up.

2 Press the PTY button to activate the PTY mode,

while the unit is in Radio (FM receiving) mode.

The Programme Type of the station being

currently received will be displayed for 5 seconds.

• If there is no receivable PTY broadcast, "NO

PTY" will be displayed for 5 seconds.

• If no RDS station can be received, the display

shows "NO RDS."

NOTE

If no button is pressed within 5 seconds after pressing

the PTY button, the PTY mode will be automatically

cancelled.

3 Press the g DN and f UP buttons within 5

seconds after activating the PTY mode to

choose the desired programme type while the

PTY (programme type) is being displayed. Each

press scrolls the programme type by one.

4 Press the PTY button within 5 seconds after

selecting the programme type to start searching

for a station in the selected programme type.

The chosen programme type indicator blinks during

searching and lights when a station is found.

If no PTY station is found, "NO PTY" will be

displayed for 2 seconds.

5 Press the F button to activate the normal mode.

The F indicator light goes out.

LIGHT M ← CLASSICS → OTHER M

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine cdm 7859 rb Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info