Bedienungsanleitung Alpine dva 9860 r (Seite 59 von 64) (Englisch)

168536

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

58-EN

To prevent external noise from entering the audio system.

• Locate the unit and route the leads at least 10

cm away from the car harness.

• Keep the battery power leads as far away from other leads as possible.

• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.

• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise

suppressors, contact them for further information.

• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

1 Antenna Receptacle

2 Audio Interrupt In Lead (Pink/Black)

Connect this lead to the Audio Interface output of a cellular

phone which provides ground shorting when a call is

received.

3 Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your

amplifier or signal processor.

4 Dimmer Lead (Orange)

This lead may be connected to the vehicle’s instrument

cluster illumination lead. This will enable the vehicle’s

dimmer control to dim the backlighting of the unit.

5 Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle’s fuse

box or another unused power source which provides (+) 12V

only when the ignition is turned on or in the accessory

position.

6 Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle.

Make sure the connection is made to bare metal and is

securely fastened using the sheet metal screw provided.

7 Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna,

if applicable.

• This lead should be used only for controlling the vehicle's

power antenna. Do not use this lead to turn on an amplifier or

a signal processor, etc.

8 Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle’s

battery.

9 ISO Power Supply Connector

! ISO Connector (Speaker Output)

" Left Rear (+) Speaker Output Lead (Green)

# Left Rear (–) Speaker Output Lead (Green/Black)

$ Left Front (+) Speaker Output Lead (White)

% Left Front (–) Speaker Output Lead (White/Black)

& Right Front (–) Speaker Output Lead (Grey/Black)

( Right Front (+) Speaker Output Lead (Grey)

) Right Rear (–) Speaker Output Lead (Violet/Black)

~ Right Rear (+) Speaker Output Lead (Violet)

+ Remote Control Input Lead (White/Brown)

Connect the external Alpine product to the remote control

output lead.

, Monitor Control Lead (White/Pink)

Connect this to the Monitor Control Lead of the touch panel-

compatible monitor.

- Video Output Connector

This connector is used in combination with the video inputs

of another video product (Touch panel compatible monitor,

etc.)

. External Junction Box Connector

Connect to the external junction Box (included)

/ External Junction Box

Use when connecting optical digital cable or the remote

control interface box.

Connect to the external junction box connector.

• Do not install the external junction box at a location subjected

to water such as under the floor mat or air conditioner. This

may cause a malfunction.

•

Do not bundle the external junction box cable with other audio cables.

Doing so may induce noise into your system.

• Keep the external junction box away from the Antenna cables

and the rear side of the unit, otherwise noise may be generated

when receiving radio broadcast.

: Digital Output Terminal (Optical)

Use when combining optical digital input compatible

products.

; Steering Remote Control Interface Connector

To steering remote control interface box.

• Use a steering remote control extension cable (included) if

necessary.

< Vehicle Display Interface Connector

Vehicle Display Interface control signals.

Connect this to the optional Vehicle Display Interface box.

• For details about connections, consult your nearest ALPINE

dealer.

= Ai-NET Connector

Connect this to the output or input connector of other product (CD

changer, Equalizer, iPod adapter*,

etc.) equipped with Ai-NET.

* When connecting iPod, the adapter KCA-420i is required. For

details about connections, refer to the manual of KCA-420i.

> Fuse Holder (10A)

? Rear Output RCA Connectors

RED is right and WHITE is left.

@ Front Output RCA Connectors

RED is right and WHITE is left.

[ Subwoofer Output RCA Connectors

RED is right and WHITE is left.

\ Power Supply Connector

] System Switch

When connecting a processor using Ai-NET, place this

switch in the EQ/DIV position. When no device is

connected, leave the switch in the NORM position.

• Be sure to turn the power off to the unit before changing the

switch position.

^ Ai-NET Cable (Included with CD Changer)

_ RCA Extension Cable (sold separately)

{ ISO/JASO Antenna Adapter (sold separately)

ISO/JASO Antenna Adaptor may be required, depending on

the vehicle.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine dva 9860 r Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info