Bedienungsanleitung Alpine HCE-C500 (Seite 19 von 24) (Englisch)

471437

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ALPINE HCE-C500 EN 68-18693Z84-A (A5)

17-EN

Installation and

Connections

Be sure to disconnect the cable from the (–) battery post

before installing your HCE-C500 series. This will reduce

any chance of damage to the unit in case of a short circuit.

Be sure to connect the colour coded leads according to

the diagram. Incorrect connections may cause the unit to

malfunction or damage to the vehicle’s electrical system.

When making connections to the vehicle’s electrical system,

be aware of the factory installed components (e.g. on-board

computer). Do not tap into these leads to provide power

for this unit. When connecting the HCE-C500 series to the

fuse box, make sure the fuse for the intended circuit of the

HCE-C500 series has the appropriate amperage. Failure to

do so may result in damage to the unit and/or the vehicle.

When in doubt, consult your Alpine dealer.

Route the cables and wiring away from hot or moving

parts, and fix them securely to avoid heat/mechanical

damage to the cable insulation, which may result in short-

circuit, fire or electric shock.

When fixing the control unit, camera, and alarm to the

vehicle with screws, attaching to weak spots may damage

vehicle parts.

If the camera is not mounted securely, shifting positions

will cause deterioration of detection performance.

The cable may break due to stress caused when opening

and closing the door/trunk of the vehicle.

If the control unit becomes wet, the electrical circuitry may

short out.

The camera is designed specifically for use with this

system. The system cannot be used with a different camera.

This product cannot be installed in or used with anything

other than a car (in other words, it cannot be used with

motorcycles, mobility vehicles, or electric wheelchairs or as

a household security camera, etc.).

CAUTION

An installation kit suitable for your vehicle

model is required to install this system.

Performance cannot be assured if you install

this system by any other means. Be sure to

check your type of vehicle before installing

the system.

Professional expertise and experience are

required to install this camera system. For

details of how to install and connect the

cameras, refer to the installation manual for

the vehicle installation kit (sold separately).

A special measuring kit is needed and

the system can only be calibrated by an

authorised ALPINE dealer. For details,

contact your ALPINE dealer.

•

Check Accessory Parts

Camera Control unit

Front camera x1

Rear camera x1

Side camera (L) x1

Side camera (R) x1

Power cable Camera cable

(for front/rear camera)

(Solderless connector)

Camera cable

(for side camera)

Camera junction cable

(for side camera)

(Including video output)

(x2 sets)

Front camera extension cable

(5.5m)

Rear camera extension cable

(8m)

Side camera (L) extension

cable (3.5m)

Side camera (R) extension

cable (3.5m)

Velcro fastener (Control unit) Self-Tapping screw

(Control unit)

(x4)

Wire clamp (large) Wire clamp (small)

(x10)

(x15)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine HCE-C500 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info