Bedienungsanleitung Alpine INE-W987D (Seite 33 von 121) (Englisch)

572055

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

33-EN

Display example for Radio main screen

Band display

Frequency display

Preset button

SEEK mode

Listening to the Radio

Press the button.

Touch [Radio] of Top banner.

The radio mode is activated and the display changes to the

Radio mode screen.

• The display content varies depending on the last band selected.

([RadioFM1], etc.)

Touch [Band] of Bottom banner to select the

desired radio band.

Each touch changes the bands as follows:

Touch [TUNE] to select the tuning mode.

* Displays only when the PTY tuning mode is selected. For

details, refer to “PTY (Programme Type) Tuning” (page 35).

• There are two modes you can select for auto tuning, DX and

Local:

- DX (Distance) mode;

Both strong and weak stations will be tuned in.

- Local mode;

Only strong stations will be tuned in.

The initial setting is DX.

Touch [], [] or [], [] to change the radio

frequency up or down respectively.

In manual mode, touch and hold to change the frequency

continuously.

Presetting Stations Manually

Tune in a desired radio station you wish to store in

the preset memory by manual or automatic seek

tuning.

Touch and hold any one of the preset buttons for at

least 2 seconds.

The selected station is stored.

Repeat the procedure to store up to 5 other stations

onto the same band.

To use this procedure for other bands, simply select the

desired band and repeat the procedure.

A total of 30 stations can be stored in the preset memory

(6 stations for each band; FM1, FM2, FM3, MW or LW).

• If a preset memory has already been set in the same preset number, it

will be cleared and the new station will be memorised.

Presetting Stations Automatically

The tuner can automatically seek and store 6 strong stations in the

selected band in order of signal strength.

After selecting the desired band, touch [A.Memo] of

Bottom banner.

The tuner automatically seeks and stores 6 strong stations into

the preset buttons in order of signal strength.

When automatic storing has completed, the station stored in the

preset 1 is selected.

If [A.Memo] is not displayed, touch [ ] or [ ] in the bottom

banner to display [A.Memo].

• If no stations are stored, the tuner will return to the original station

you were listening to before the automatic storing procedure began.

• You can cancel this process by touching [A.Memo] while the tuner is

automatically seeking stations. Cancelling will return the tuner

preset to the previous setting.

Tuning to Preset Stations

You can tune in the preset stations in memory on either band using its

preset number.

Touch [Band] of Bottom banner repeatedly until the

desired band is displayed.

Touch any one of the preset buttons that has a

station stored to it.

The preset station is received.

Radio

FM-1 FM-2 FM-3 MW LW FM-1

DX SEEK Local SEEK MANUAL PTY*

Touch [ ], [ ]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine INE-W987D Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine INE-W987D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info