Bedienungsanleitung Alpine INE-W987D (Seite 56 von 121) (Englisch)

572055

Zoom out

Zoom in

Vorherige Seite

1/121

Nächste Seite

56-EN

Adjusting the Frequency

Touch [] or [] of “Freq.” to adjust the frequency of the

selected band.

Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps)

Adjusting the Level

Touch [] or [] of “Level” to adjust the level of selected

band.

Setting contents: -7 to +7 (Initial setting: 0)

Setting the Bandwidth

Touch [] or [] of “Q Adjust” to select the bandwidth.

Setting contents: 1 (Initial setting) / 2 / 3

To adjust another band, repeat step 1, and adjust all

bands.

To store the adjusted setting value, touch and hold

[Preset1], [Preset2], or [Preset3] for at least 2

seconds.

• BAND2 and BAND8 are the same as the Bass and Treble controls.

Their Level adjustment can also be controlled by pressing and

holding /AUDIO and selecting Bass Level or Treble Level. Refer

to “Easy Sound Setup mode” (page 25).

• Settings exceeding the frequency of adjacent bands are not available.

• While adjusting the Parametric EQ, you should consider the

frequency response of the connected speakers.

• When the Parametric EQ is adjusted, the Equalizer Presets are

overridden.

• When Equalizer Presets is set, the linked Parametric EQ settings are

also changed. We recommend storing Parametric EQ settings in a

Preset in advance.

• Touch [Flat] to initialise all values.

• The Parametric EQ setting can be configured when Defeat is “Off”.

Calling the Parametric EQ adjusted value

Calling the pre-set Parametric EQ adjusted value.

Touch [Preset1], [Preset2], or [Preset3] on the

Parametric EQ screen.

The setting stored in the Preset will be recalled.

Adjusting the Time Correction

(Time Correction)

[Time Correction] is selected on the Sound setup menu in step 3. Refer

to “Sound Setup Operation” (page 53).

Before performing the following procedures, refer to “About Time

Correction” (page 57).

Setting item: Time Correction

Touch [cm], [inch] or [ms] to select mode for

making adjustments.

Each time you touch, the onscreen button and correction

mode changes.

cm/inch: Adjust listening position and distance from each

speaker.

ms: Adjust time.

Touch [] or [] for each speaker to adjust the

time or distance.

0.0 msec to 9.9 msec (0.1 msec/step)

0.0 cm (0.0 inch) to 336.6 cm (132.7 inch) (3.4 cm/step)

All speaker setting values are adjustable in the range of 15 ms

or 510 cm.

To store the adjusted setting value, touch and hold

[Preset1], [Preset2], or [Preset3] for at least 2

seconds.

• Touch [Flat] to set all values to 0.0.

• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot

be edited (refer to page 54).

• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be

edited (refer to page 54).

Calling the Time Correction Value

Calling the pre-set time correction value.

Touch [Preset1], [Preset2], or [Preset3] on the time

correction screen.

The setting stored in the Preset will be recalled.

Band1: 20 Hz~100 Hz (63 Hz)

Band2: 63 Hz~315 Hz (125 Hz)

Band3: 125 Hz~500 Hz (250 Hz)

Band4: 250 Hz~1 kHz (500 Hz)

Band5: 500 Hz~2 kHz (1 kHz)

Band6: 1 kHz~4 kHz (2 kHz)

Band7: 2 kHz~7.2 kHz (4 kHz)

Band8: 5.8 kHz~12 kHz (8 kHz)

Band9: 9 kHz~20 kHz (16 kHz)

Correction mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine INE-W987D Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine INE-W987D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info