Bedienungsanleitung Alpine IVE-W560BT-R (Seite 11 von 96) (Deutsch, Englisch, Französisch)

661050

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

11-EN

Initial System Start-Up

Press the RESET switch when using the unit for the ﬁrst time, after

changing the car battery, etc.

1 Turn off the unit power.

2 Press RESET switch with a ballpoint pen or similar

pointed object.

RESET switch

Note

Pressing the reset button will erase the clock setting and some

stored contents.

Setting the Clock

1 Press HOME, then touch [Settings].

2 Touch

then touch [Clock Adjust].

The setting display appears.

3 Touch

to set the hour and minute.

4 Touch [Set].

The setting is complete.

To activate/deactivate the CT function (page 13), touch [Clock Time].

Preparing a BLUETOOTH Device

You can enjoy music, or perform handsfree calling, by connecting a

suitable BLUETOOTH device (mobile phone, audio device, etc.). For

details on connecting a BLUETOOTH device, refer to the operating

instructions supplied with the device. Before connecting, turn down

the volume of this unit; otherwise, loud sound may result.

Pairing and connecting with a BLUETOOTH

device

When connecting a BLUETOOTH device for the ﬁrst time, mutual

registration (called “pairing”) is required. Pairing enables this unit and

other devices to recognize each other.

1 Press HOME, then touch [Settings].

2 Touch

3 Touch [Bluetooth Connection], then set the signal to

[ON].

The BLUETOOTH signal of this unit is activated and

appears

on the status bar.

4 Touch [Pairing].

The unit enters pairing standby mode.

5 Perform the pairing procedure on the BLUETOOTH

device to detect this unit.

6 Select “IVE-W560” shown in the display of the

BLUETOOTH device.

7 If passkey* input is required on the BLUETOOTH device,

input [0000].

* Passkey may be called “passcode,” “PIN code,” “PIN number,”

“password,” etc., depending on the BLUETOOTH device.

8 Select this unit on the BLUETOOTH device to establish

the BLUETOOTH connection.

or lights up when the connection is made.

Note

While connected to a BLUETOOTH device, this unit cannot be

detected by another device. To enable detection, terminate the

current connection.

Connecting with a paired BLUETOOTH

device

This chapter explains how to connect manually to registered

BLUETOOTH devices.

1 Make sure that the BLUETOOTH signals both on this unit

(page 19) and the BLUETOOTH device are activated.

on the status bar indicates that the BLUETOOTH signal on this

unit is on.

2 Operate the BLUETOOTH device to connect to this unit.

or appears.

When the ignition is turned to on with the BLUETOOTH signal

activated, this unit searches for the last-connected BLUETOOTH

device, and if possible connection is made automatically.

Note

If this unit cannot detect the last-connected BLUETOOTH device,

touch [Reconnect] to search for the last-paired device again.

If the problem is not solved, follow the pairing procedure.

To install the microphone

To capture your voice during handsfree calling, you need to install

the microphone (included).

For details on how to connect the microphone, refer to the supplied

“Installation/Connections” guide.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine IVE-W560BT-R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info