Bedienungsanleitung Alpine iXA-W407BT (Seite 10 von 73) (Englisch)

471357

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

8-EN

Turning Power On or Off

Some of this unit’s functions cannot be performed while the vehicle is in

motion. Be sure to stop your vehicle in a safe location and apply the

parking brake, before attempting these operations.

Press

SOURCE to turn on the unit.

• The unit can be turned on by pressing any button. The unit is also

automatically turned on if an iPhone/iPod or USB memory is

connected.

Press and hold

SOURCE for at least 3 seconds to

turn off the unit.

• The monitor may be dim during low temperature and immediately

after turning on the power. The brightness will return to normal as

time elapses.

• The iXA-W407BT is a precision device. With gentle handling, its

unique capabilities can be enjoyed for a long time.

Adjusting the Volume

Adjust the volume by pressing or .

Volume decreases/increases continuously by pressing and

holding

or .

Volume: 0 - 35

• The MUTE function can be performed by using the supplied remote

control.

How to view the Display

• Be sure to touch the button lightly with the pad of your finger on the

display to protect the display.

• If you touch a button and there is no reaction, remove your finger

from the display, and try again.

Here is an example explanation for the Radio mode display on how to

recall a source.

Press

SOURCE to activate mode switching

screen.

Slide the display horizontally with your finger to

select Audio/Visual mode.

Each time you slide the display, the mode switches

circularly in the following order:

Audio/Visual Navigation*

Camera*

Telephone*

Multi Info Audio/Visual

Displayed only when NAV. IN is set to ON. Refer to “Setting

Navigation Mode” (page 21).

Displayed only when Camera IN is set to RCA or DIRECT. Refer to

“Setting the Rear Camera Input” (page 21).

Displayed only when Bluetooth IN is set to BUILT-IN. Refer to

“Setting the BLUETOOTH Connection (Bluetooth IN)” (page 23).

• The mode can also be switched by pressing and .

• If the current mode is not Audio/Visual mode, you can switch to the

Audio/Visual mode directly by pressing

SOURCE.

Display example for mode switching screen

Changes to the Rear Selection screen when “Setting the

Picture Output” (page 22) is set to ON.

Touch and hold [SETUP] for at least 2 seconds to

change to the SETUP selection screen.

Displays the name and image of the current mode.

Displays the icons of the five modes.

(icon of the current mode is highlighted.)

Slide the display vertically with your finger, or press

SOURCE repeatedly to select RADIO source.

Touch the RADIO source window displayed in the

centre of the screen.

The RADIO source is activated and the display changes to

the RADIO main screen.

Soft button operation

About the button descriptions used in this Owner’s Manual

• Soft buttons, ones found in the display, are shown in bold

enclosed in brackets, [ ] (e.g. [SETUP]).

• Whenever a soft button and a head unit button have the same

function, the explanations in this Owner’s Manual will describe

the function of the soft button.

Recalling the Source

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine iXA-W407BT Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alpine iXA-W407BT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info