Bedienungsanleitung Alpine mdm 7741 r (Seite 7 von 21) (Englisch)

168348

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

5-EN

Subwoofer On and Off

1 Press and hold the c (Eject) button for at least 3

seconds.

With each press, subwoofer is toggled On or Off.

NOTES

• Initial mode is "SUBW OFF."

• Set to "SUBW OFF" unless the subwoofer is used.

• When the subwoofer is turned on, the subwoofer

output level can be adjusted. For more details,

refer to the Adjusting Volume/Bass/Treble/Balance/

Fader.

Adjusting Source Signal Levels

If the difference in volume level between the MD

player and FM radio is too great, adjust the FM

signal level as follows.

1 Press and hold the INTLZ button for at least 3

seconds.

2 Press the Preset 1 button to select the FM signal

level HI (High) or LO (Low) to make the signal

levels between the FM band and MD player

closer.

3 Press the INTLZ button for more than 3 seconds

to cancel the adjusting mode.

Adjusting Volume/Bass/Treble/

Balance (Between Left and Right)/

Fader (Between Front and Rear)

1 Press the MODE button repeatedly to choose the

desired mode.

Each press changes the modes as follows:

NOTES

• If the

5 or

6 button is not pressed in 5 seconds after

selecting the BASS, TREBLE, BALANCE, or FADER

mode, the unit automatically sets in the VOLUME

mode.

• When the subwoofer is set to ON, the level of the

subwoofer can be adjusted.

2 Press the

and

buttons until the desired

sound is obtained in each mode.

NOTE

The settings of the Bass and Treble will be individually

memorized for each source (FM, MW(LW) and MD)

until the setting is changed. Depending on the

connected devices, some functions and display

indications do not work.

Turning Loudness On/Off

Loudness introduces a special low- and high-

frequency emphasis at low listening levels. This

compensates for the ear's decreased sensitivity

to bass and treble sound.

1 Press the LOUD button to activate or deactivate

the loudness mode.

The display shows "LD" when the loudness

mode is activated.

Setting Bass Frequency

The bass control centre frequency can be set at

60, 80, 100 or 200 Hz.

1 Press and hold the B.C. (Bass Control) button

for at least 3 seconds to turn on the bass control

settings.

2 Press the DN g or f UP button to select

the desired Bass centre frequency.

Each press changes the centre frequency as

follows: 60 Hz, 80 Hz, 100 Hz and 200 Hz.

NOTE

If no buttons are pressed within 5 seconds, the bass

control settings will be turned off automatically.

3 Press the B.C. (Bass Control) button for more

than 3 seconds to turn off the bass control

settings.

NOTE

Initial mode is 80Hz.

Adjusting the Contrast

It is possible to adjust the display contrast in

case the display is difficult to view.

1 Press and hold the INTLZ button for at least 3

seconds.

2 Press the Preset 4 button to select the contrast

adjusting mode.

3 Press the DN g or f UP button to adjust

the contrast.

The contrast can be adjusted between levels of –

5 and +5.

4 Press the INTLZ button for more than 3 seconds

to activate the normal mode.

→ VOL → BASS →TREB

FAD ← BAL ←

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine mdm 7741 r Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info