Bedienungsanleitung Alpine PXA-H701 (Seite 7 von 52) (Englisch)

66420

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

5-EN

Adjusting the input level

Using the analog, RCA-type connections, the

PXA-H701’s input level must be preset from the

head unit.

Adjust the input level using a sound source with

a high recording level (such as pop or rock

music).

1 Turn on the head unit’s power.

2 Turn the Rotary encoder on the main unit

counterclockwise and set the volume level to “0”.

3 Gradually increase the volume of the head unit

until “INPUT LEVEL OVER” appears in the

display.

Reduce the volume slightly from this position,

until “INPUT LEVEL OVER” display just turns off.

This completes the setting.

Do not change the head unit volume level from

this optimum setting. Use the PXA-H701, only,

for changing the volume level.

NOTE

Switch to the spectrum analyzer display mode or the

input channel display mode before adjusting the input

level. (See page 29)

Adjusting the volume, balance, fader and subwoofer

After determining the input level, adjust the

volume, balance, fader and subwoofer from the

PXA-H701. Be careful not to make these

adjustments on the head unit.

1 Press the ENTER button and select the mode to

be adjusted.

2 Turn the Rotary encoder within 5 seconds and

adjust to the desired level.

VOLUME : 0 ~ 35

BALANCE : L15 ~ R15

FADER : F15 ~ R15

Sub.W LEVEL : 0 ~ +15

NOTE

When the subwoofer is set to “OFF”, the Sub.W

LEVEL adjustment is ineffective.

Using with RCA-type or optical cable

connections (non Ai-NET connections)

(only when using the control unit sold

separately)

Switching the input

The PXA-H701 is equipped with three sets of

analog signal inputs and three sets of digital

signal inputs. For further information about

connections, see Page 36.

1 Press the SETUP button.

The setup mode is set.

2 Turn the Rotary encoder to select the “INPUT

SELECT” mode, then press the ENTER button.

3 Turn the Rotary encoder to select the input

mode, then press the ENTER button.

4 Press the SETUP button repeatedly to quit the

setup mode.

NOTE

Non Ai-NET connections

Alpine products are equipped for a bus connection

system called “Ai-NET” which can only be used for

connections between Ai-NET products.

The PXA-H701 is an Ai-NET product, but is designed to

allow connections to other (non Ai-NET) products as

well. Thus RCA-type and optical cable connections are

also possible.

Connections to non Ai-NET products are referred to as

“non Ai-NET connections”.

Analog 1 Analog 2 Analog 3

Digital 3 Digital 2 Digital 1

VOLUME FADERBALANCE

Sub.W LEVEL

Using with Ai-NET connections

When Ai-NET connections are used, the volume,

subwoofer, balance and fader are adjusted from

the head unit (they cannot be adjusted from the

PXA-H701). However, BASS and TREB can not

be adjusted from the head unit, so adjust them

from PXA-H701.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine PXA-H701 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info