Bedienungsanleitung Alpine RUX-C800 (Seite 20 von 67) (Englisch)

471407

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

18-EN

01GB06PXAH800.fm

ALPINE PXA-H800_EN 68-13530Z65-A (B5)

From a PC

Move the microphone to a spot specified in the

screen and position it firmly.

• The microphone should be placed at shoulder height.

Click [Measure]. When the measurement start

screen appears, click [START].

Countdown will start.

During the 10 second countdown, go outside the vehicle

and close the door.

A test signal will be output from the speakers to measure the

acoustic characteristics of the cabin. Do not open any

doors until the finish message appears on the screen. If

external noise interferes with the measurement, click the

[Measure] again to re-measure.

• Measurement takes approximately 5 to 15 minutes.

• If you want to stop measurement, click [CANCEL].

Click [OK] when a completed message appears.

When measurement for Position 1 is completed,

move the microphone to the next measuring position

and secure it following the guidance on the screen.

When the microphone is properly located, repeat

Step 13 following the guidance on the screen.

• You can perform measurement from up to 6 listening

positions.

• We recommend that you should take measurements from

at least 2 listening positions.

• To close measurement, go to Step 16.

• For more accurate measurement, you can make

measurements from 6 listening positions. However, it

takes approximately 70 minutes to complete the entire

procedure. Therefore, be sure to charge the vehicle

battery while taking measurements.

• If no microphone is connected, a confirmation message will be

displayed and measurement will not be carried out. Click [OK] to

cancel the indication.

• If you want to re-measure from the same position, click [Reset].

When measurement is complete, click [Result].

The result screen will be displayed.

The adjustment result when the Target Curve is

“REFERENCE” will be displayed.

If you want to select another target curve, go to Step 17.

If you want to save the adjustment result, go to Step 19.

Click [Target Curve Select].

The Target Curve Selection screen will be displayed.

Select and click the target curve you want. Then,

click [OK].

The adjustment result for the selected Target Curve will be

displayed.

REFERENCE:

Enjoy the rhythm and balance of music to the best

acoustic effect, suitable for the vehicle interior.

Reference With Mid-range Comp.:

Select this if the tweeter and midrange speakers are

installed in the dashboard, and mid or high range

harshness is apparent.

LINEAR:

A linear (flat) acoustic effect is actualized. This setting

recreates the balanced sound of a studio listening

room.

USERS:

You can select this only when you have adjusted the

curve. Refer to “Adjusting and Saving the Target

Curve” (page 19).

• If you are not satisfied with the measurement result, click [Re-

Measure] to perform measurement again.

Click [Send Filter].

The Memory selection screen will be displayed.

The name of the curve currently selected.

01GB00PXAH800.book Page 18 Tuesday, February 8, 2011 9:04 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine RUX-C800 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info