Bedienungsanleitung Alpine TDA-7588RB (Seite 33 von 44) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Schwedisch)

466963

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

31-EN

Changer

6 Press and hold the TITLE button for at least 3

seconds to record the title.

NOTES

• When the memory capacity for the disc titles is used

up, the display shows "FULL DATA" to indicate that

no more title can be memorized.

• When you want to erase a title, enter the "

symbol into all spaces.

Erasing Disc Title

1 Press the TITLE button to select the disc titling

mode. Then press and hold it for at least 3

seconds.

2 Press and hold the :/J button for at least 2

seconds to activate the title erasing mode.

The disc title in the display will blink.

3 Press the g DN or f UP button repeatedly

until the disc title you want to erase is displayed.

4 Press and hold the :/J button for at least 2

seconds to erase the disc title displayed.

5 Press and hold the TITLE button for at least 3

seconds to cancel the disc title erasing mode.

Searching for Titled Discs

If a CD is titled, you can do a search for it. (To title

CDs, refer to "Titling Discs" on page 24.)

1 Press and hold the T.S.M. button for at least 2

seconds. The title blinks in the display.

2 Press the g DN or f UP button to select

the desired disc title.

3 Press the T.S.M. button to play the selected disc.

The unit will automatically search for the disc

and begin play.

4 Press the T.S.M. button for at least 2 seconds to

cancel the disc searching mode.

NOTE

This function cannot be performed when using a multi-

changer switching device.

Multi-Changer Selection

Alpine's Ai-NET system will support up to 6 CD

Changers. When operating two or more changers,

the KCA-400C (Multi-Changer Switching device)

must be used. If you use 1 Switching device, you

can connect up to 4 CD Changers. If you use 2

Switching devices, you can connect up to 6 CD

Changers. When using KCA-410C (Versatile Link

Terminal), you can connect two changers and two

external outputs (AUX).

1 Press the SOURCE button to activate the CD

Changer mode.

Alternatively, press the SOURCE button on the

Remote Control (RUE-4187) to activate the CD

Changer mode. Proceed to Step 3 below to

select the desired CD Changer.

2 Press the BAND button or the RUE-4187 to

activate the CD Changer Selection mode.

3 The CD Changer Selection mode remains active

for 3 seconds after Step 2 is performed. Press

the BAND button until the desired CD Changer

indicator appears on the display.

NOTE

If the selected CD Changer is not connected, the display

will show "NO CHGRX."

Alternatively press the BAND button on the

Remote Control until the desired changer

indicator appears on the display.

4 To operate the selected changer, see "CD

Operation" section.

NOTE

For further details about the external input (AUX) when

using KCA-410C, see ”Setting the AUX Mode (V-Link)"

on page 10.

SOURCE

BAND

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine TDA-7588RB Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info