Bedienungsanleitung Alpine tda 7592 r (Seite 33 von 38) (Englisch)

168570

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

31-EN

Installation and Connections

Before installing or connecting the unit, please

read the following and pages 2 and 3 of this

manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire

or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE

GROUND.

(Check with your dealer if you are not sure.) Failure to do

so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM

THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due

to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other

equipment. Doing so will exceed the current carrying

capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN

DRILLING HOLES.

When drilling holes in the chassis for installation, take

precautions so as not to contact, damage or obstruct pipes,

fuel lines, tanks or electrical wiring. Failure to take such

precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND

CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or

any other safety-related system), or tanks should NEVER

be used for installations or ground connections. Using

such parts could disable control of the vehicle and cause

fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT

OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If

swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT

HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper

movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY

EXPERTS.

The wiring and installation of this unit requires special

technical skill and experience. To ensure safety, always

contact the dealer where you purchased this product to

have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL

THEM SECURELY.

Be sure to use only the specified accessory parts. Use of

other than designated parts may damage this unit

internally or may not securely install the unit in place.

This may cause parts to become loose resulting in hazards

or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR

PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like

the seat rails) or sharp or pointed edges. This will prevent

crimping and damage to the wiring. If wiring passes

through a hole in metal, use a rubber grommet to prevent

the wire's insulation from being cut by the metal edge of

the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH

MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence

of moisture or dust. Moisture or dust that penetrates into

this unit may result in product failure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine tda 7592 r Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info