1 2
Installation
English
Installing the Monitor
Caution:
If your vehicle has passenger side air bags, make sure the monitor is not
mounted in an area where the air bag will be deployed.
1 Assemble the mounting bracket and temporarily mount the monitor.
Note:
Always use the TV mounting bracket supplied.
2 Carefully choose the installation location.
Select a location that is as flat as possible. Temporarily mount the unit there
using double-stick tape.
Notes:
• Mounting hints
• Top of the monitor should not exceed the top of the dash-board when
viewed from the drivers seat.
• The mounting surface should be strong and stable.
• Position the monitor and viewing angle so it can be easily seen.
• Do not install this unit in a location that will obstruct the operation of any
safety device (such as air bags or passive restraint systems).
• If the surface of the dash board is finished with other than plastic such as
leather, wood, or cloth, damage may occur when the mounting bracket is
removed.
3 Peel the protective paper from the double stick tape on the mounting bracket.
Secure the bracket at the installation location.
Clean the installation location with the cleaner supplied.
Notes:
• Warm the installation location with a dryer before putting the mounting
bracket into place.
• Do not apply force or moisture for 24 hours after installation.
• If the bracket is not attached securely, mount the bracket with the screws
provided.
• ★ : If the mounting surface is curved, reform the base of the mounting
bracket to match its shape.
4 Connect the monitor.
Insert the connector into the back of the monitor until a click is heard.
5 Mount the monitor on the mounting bracket.
Align the threaded hole on the bottom of the monitor to the mounting thumb-
screw. Secure the monitor by rotating the thumbscrew.
Use the cord clamper to dress the cord to prevent possible entanglements.
6 Adjust the height and angle of the monitor for the best viewing angle.
Determine the height and angle. Tighten the height adjusting screw and the
angle adjusting screw securely to fix the monitor.
Monitor
Dashboard
Monitor Mounting Screw
Mounting Bracket
3
Remove the monitor from the mounting bracket.
Operations
Screen Display ON/OFF
1 Set the Main POWER switch to the STAND-BY position. The main power
lamp will illuminate.
2 When you have finished using the monitor, set the Main POWER switch to the
OFF position. The main power lamp will turn off.
Notes:
• When you turn off the car's ignition switch, make sure the monitor's power
is also turned off. If the monitor is left in the STAND-BY position, it will
slowly drain the car's battery.
• On Screen Display
The operation contents will be displayed for 3 seconds.
Adjusting the Volume
1 Rotate the VOLUME control UP to increase the volume and DOWN to de-
crease.
Changing the Brightness of the Back Light (Dimmer Function)
1 Setting the DIMMER switch.
HIGH : Maintains bright backlighting.
AUTO : Adjusts the brightness automatically, depending upon the vehicle's
driving lights.
Headlights off = brighter
Headlights on = darker
Notes:
• Contents displayed on the screen may remain on the screen temporarily; this
is a residual image effect peculiar to the LCD and not due to failure.
• The screen may lose contrast when used in cold temperature conditions.
In Case of Difficulty
Symptom
No function
or display.
Unclear
picture
display.
No picture
display.
Poor picture
brightness.
Spots or
dotted lines/
stripes
appear.
Cause
Car's ignition is off.
Incorrect connections.
Vehicle's battery is weak.
Monitors power is Off.
Fluorescent tube is exhausted.
Brightness control is set for
minimum brightness control.
Navigation system's mode set
incorrectly.
Protective circuit is on because of
high temperature.
Incorrect or open connection with
the Monitor.
Brightness control is not set to the
proper positions.
Caused by neon signs, high-
voltage power lines, CB transmit-
ter, other vehicle's spark plugs,
etc.
Solution
Turn the ignition on.
Check connection and remedy.
Check the voltage of vehicle's
battery.
Turn the monitor's power on.
Replace the fluorescent tube.★
Adjust the monitor's brightness in
the navigation system's set-up
mode.
Switch to the correct mode using
the navigation system's set-up
remote control.
Wait until the temperature inside
the vehicle comes down to the
operating temperature range
(45° C).
Check the connection and rem-
edy.
Check the dimmer switch on the
side of the monitor or adjust the
brightness in the navigation
system's set-up mode.
Change the location of your
vehicle.
Specifications
1
2
•
•
•
•
•
•
3
•
•
•
•
4
5
6
1
2
•
•
1
1
•
•
MONITOR
Screen Size .................................................................................................................... .............. 6-type
Display System ............................................ Low reflection rear projection type TN liquid crystal panel
Drive System ........................................................................ Active matrix drive, normally white display
Number of Picture Elements ........................................................... 228, 480 pcs. (H:960 x V:238 dots)
Light Source ......................................... Internal optical system (U-type cold cathode fluorescent tube)
Luminance Selector ................................................................ 2-step (luminance auto-selector built-in)
Speaker ......................................................................................................... φ 36mm dynamic speaker
Volume Control ............................................................................................................... Rotary volume
Dimensions (W x H x D) ............................................................................................ 171 x 127 x 33mm
Weight ............................................................................................................................................ 510g
φ
If you encounter a problem, please review the items in the following check list.
This guide will help you isolate the problem if the unit is at fault. Otherwise, make
sure the rest of your system is properly connected or consult your authorized
Alpine dealer.
★
★
Monitor
MOBILE COLOR MONITOR
TME-M006SE
POWER
VOLUME
DIMMER
POWER
HIGH
AUDIO
STANDBY
OFF
DIMMER Switch/
VOLUME Control/
Main POWER Lamp/
Remote Control Sensor/
Main POWER Switch/
Connections
Connection with TV Tuner (TUE-T011) (Sold Separately)
• The unit can be operated with the remote controller attached with the TV
Tuner. For details, refer to the Owner's Manual of the TV Tuner (TUE-T011).
•
Screen Display ON/OFF Adjusting the Volume
1 1
VOLUME
2
Changing the Brightness of the Back Light
(Dimmer Function)
6
Height Adjustment Screw
Angle Adjustment Screw
4
5
Monitor Connector Terminal
Monitor
Monitor Connector
Cord Clamp
Mounting Hole
Monitor Mounting Screw
★
Double Stick Tape
Mounting Screws (Included)
1
DIMMER
HIGH
AUTO
Mounting Hole
DISPLAY OUTPUT POWER SUPPLY
1234
ANTENNA INPUT VIDEO INPUT
VIDEO OUTPUT
VIDEO L R AUDIO VIDEO L R AUDIO
(MONO)
NAVIGATION INPUT
COLOR CONTROL
ON
OFF
TV TUNER/DIVERSITY UNIT
TUE-T011
RGB INPUT
LCD COLOR MONITOR
TME-M006SE
POWER
TUE-T011 (TV Tuner) (Sold Separately)
Monitor
★ The fluorescent tube replacement is not free of charge even within the war-
ranty period, for the tube is an article of consumption.
POWER
POWER
STANDBY
OFF
POWER
STANDBY
OFF