Bedienungsanleitung Alpine TMX-310U (Seite 15 von 128) (Englisch)

536990

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

13-EN

Before installing or connecting the unit, please

readthefollowingandpages3and4ofthismanual

thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in re or product

damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE

GROUND.

(Check with your dealer if you are not sure.) Failure to do so may

result in re, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM

THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical

shorts.

DO NOT ALLOW CABLES TO BECOME

ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent

obstructions when driving. Cables or wiring that obstruct or hang up

on places such as the steering wheel, gear lever, brake pedals, etc., can

be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment.

Doing so will exceed the current carrying capacity of the wire and

result in re or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN

DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions

so as not to contact, damage or obstruct pipes, fuel lines, tanks or

electrical wiring. Failure to take such precautions may result in re.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR

STEERING SYSTEMS TO MAKE GROUND

CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other

safety-related system), or tanks should NEVER be used for

installations or ground connections. Using such parts could disable

control of the vehicle and cause re, etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT

OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a

physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT

HINDER VEHICLE OPERATION, SUCH AS THE

STEERING WHEEL OR SHIFT LEVER.

Doing so may obstruct forward vision or hamper movement, etc., and

result in a serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY

EXPERTS.

The wiring and installation of this unit requires special technical skill

and experience. To ensure safety, always contact the dealer where you

purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL

THEM SECURELY.

Be sure to use only the specied accessory parts. Use of other than

designated parts may damage this unit internally or may not securely

install the unit in place. This may cause parts to become loose

resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR

PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat

rails) or sharp or pointed edges. This will prevent crimping and

damage to the wiring. If wiring passes through a hole in metal, use a

rubber grommet to prevent the wires insulation from being cut by the

metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH

MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture

or dust. Moisture or dust that penetrates into this unit may result in

product failure.

Precautions

• Be sure to disconnect the cable from the vehicle's (-) battery post

before installing your unit. This will reduce any chance of damage

to the unit in case of a short-circuit.

• Be sure to connect the color coded leads according to the diagram.

Incorrect connections may cause the unit to malfunction or damage

to the vehicle's electrical system.

• When making connections to the vehicle's electrical system,

be aware of the factory installed components (e.g. on-board

computer). Do not tap into these leads to provide power for this

unit. When connecting the unit to the fuse box, make sure the fuse

for the intended circuit of the unit has the appropriate amperage.

Failure to do so may result in damage to the unit and/or the vehicle.

When in doubt, consult your ALPINE dealer.

• The unit uses female RCA-type jacks for connection to other

units (e.g. amplier) having RCA connectors. You may need an

adaptor to connect other units. If so, please contact your authorized

ALPINE dealer for assistance.

IMPORTANT

Please record the serial number of your unit in the space provided

below and keep it as a permanent record. The serial number plate

is located on the bottom of the unit.

Installation and Connections

SERIAL NUMBER: ____________________________

INSTALLATION DATE: _________________________

INSTALLATION TECHNICIAN: __________________

PLACE OF PURCHASE: _______________________

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine TMX-310U Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info