110622
18
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
16
8 Exit the Alarm Set mode.
PresstheALARM1buttononthespeakersystemortheENTER
button on the wireless remote to exit the Alarm Set mode. The
speaker system will also automatically exit the Alarm Set mode after
5secondsofinactivity.
NOTE When exiting the Alarm Set mode, the alarm is automatically turned
on.Toturnoffthealarm,pressthecorrespondingALARM1/ALARM2button.
NOTE The alarm time is displayed in the lower right-hand corner of the LCD
display when you turn the alarm on. If both alarms are active, the time for
Alarm1willbedisplayedinthelowerright-handcorner.
NOTE Ifbothalarmsareactiveatoverlappingtimes,Alarm1takes
precedenceoverAlarm2.
NOTE This Altec Lansing Moondance Home speaker system features
a built-in backup battery system to provide continuous clock settings in
the event of a power failure. If a power failure occurs or the AC cord is
accidentally disconnected, the display will not remain lit and the alarm will
not function, but the current time will be maintained.
NOTE If “iPod” is selected as the alarm source but no iPod is docked when
thealarmgoesoff,thebuzzeralarmwillsoundinstead.
NOTE IftheiPod,FMradioorAUXINisplayingwhenthealarmgoesoff
and a different alarm source has been selected, the speaker system will
switch to the selected alarm source.
How to Set Alarm 2
Repeattheabovesteps,substituting“Alarm2”for“Alarm1.”
How to Use Alarm 1
1 Press the ALARM1 button on either the speaker system or the
wireless remote.
Thisactivatesthealarm.TheAlarm1iconintheupperleft-hand
corner of the LCD display will light and the alarm time will display in
the lower right-hand corner of the display.
2 When the clock times matches the alarm time, the alarm
sounds, the Alarm 1 icon flashes, and the whole display
flashes.
The alarm gets progressively louder until it reaches the set level. After
atotalof59minutes,thealarmwillsilenceitself.
3 To dismiss the alarm, press the ALARM1 or ALARM2 buttons
on the speaker system or the ALARM1 or ALARM2 buttons on
the wireless remote.
4 To disable the alarm before its time is up, press the Alarm1
button.
How to Use Alarm 2
Repeattheabovesteps,substituting“Alarm2”for“Alarm1.”
How to Use the Snooze Feature
PresstheSNOOZEbuttononcetosilencethealarmforaperiodof
5minutes.
Setting the Alarm
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Altec Lansing M-302 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info