Bedienungsanleitung Alto COMPACT 1050 X-TRA (Seite 5 von 11) (Englisch)

586744

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

2.0 Operating Instructions

2.1 Operating facilities

 Start/stop switch (1).

 Spray handle with safety catch (5).

2.2 Connection

1. Attach the high pressure hose (4) to the high

pressure water outlet of the machine (2).

2. Attach the spray handle (5) to the high pressure

hose (4). Prior to operating the machine please

ensure that the high pressure hose has been

completely uncoiled. Whilst the machine is in

operation the hose MUST NOT loop.

3. Mount the nozzle or any other equipment you

want to use.

4. Connect the machine to the water and power

supplies.

The pressure washer is now ready for operation.

2.3 Start

1. Unlock the spray handle.

2. Activate the trigger and let the water run until all

air has escaped from hoses and pump.

3. Press the start/stop switch (1) into pos. "I".

2.4 Operation

1. The spray lance is affected by a thrust

during operation - therefore always hold

it ﬁ rmly with both hands. NOTE: Point the

nozzle at the ground.

2. Activate the trigger of the spray handle.

3. Always adjust the distance and thus the pres-

sure of the nozzle to the surface which is to be

cleaned. (Note! pressure and spray angle can be

regulated on the nozzle).

NOTE: Do not cover the machine during operation.

If the machine is left or not used for 3 minutes, it

must be switched off on the start/stop switch (1)

(press the switch into pos "O").

Secure the spray handle against inadvertent use by

locking the trigger with the safety catch.

Operating Instructions EN

2.5 End of operation

1. Stop the machine by pressing the start/stop

switch (1) into pos. "O".

2. Disconnect the plug from the socket.

3. Shut off the water supply and ac ti vate the trigger

to relieve the machine of pres sure.

Concerning storage, please refer to section 5.0.

3.0 Accessories EN

Only use original accessories.

3.1 POWERSPEED

nozzle

The pressure washer is supplied with a

POWERSPEED

nozzle (8). This nozzle has a pen-

cil jet which rotates through 360° when in use. This

gives increased performance for removing difﬁ cult

and stubborn marks. To ﬁ t the POWERSPEED

nozzle, proceed as follows:

1. Push the POWERSPEED

nozzle (8) into the

bayonet coupling of the spray handle (5) and twist

in a clockwise direction until it clicks into place.

3.2 Foam sprayer

To ﬁ t the foam sprayer (9), proceed as follows:

1. Push the foam sprayer (9) into the bayonet

coupling of the spray handle (5) and twist in a

clockwise direction until it clicks into place. En-

sure that the clear plastic pipe is ﬁ tted to the foam

sprayer.

2. Fill the bottle with a suit a ble biodegradable de-

ter gent.

3. Screw the bottle onto the foam sprayer.

Extra equipment

Multispeed

nozzle Universal adjustable nozzle:

Nozzle forward:

Low pres su re.

Nozzle backward:

High pressure.

Nozzle turned left:

20° spray angle.

Nozzle turned right:

No spray angle (pencil jet).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alto COMPACT 1050 X-TRA Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alto COMPACT 1050 X-TRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info