Bedienungsanleitung Alto-WAP SQ 15 (Seite 3 von 9) (Englisch, Französisch)

608906

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Before connecting a

tool, ensure that

both the cleaner and

the tool are

switched off.

For the working

pressure of the

pneumatic tool to be

connected, see table

'Technical Data'.

SQ 17 Gallon AS/PE 2:

• Connect the

pneumatic tool (two

tools can be

connected at the same

time) to the quick

coupler on the control

panel.

• Connect the

compressed air supply

to the nipple (Fig.1,

Pos. 9).

Before connecting a

tool, ensure that

both the cleaner and

the tool are

switched off.

For the working

pressure of the

pneumatic tool to be

connected, see table

'Technical Data'.

WARNING:

To avoid risk of elecrical

shock, do not expose to

rain.

PICKING UP DRY

SUBSTANCES

Before picking up dry

substances, the bag-type

filter should always be

installed in the tank. It is

then easy to dispose of

the material picked up

and the service life of the

main filter element is

significantly increased. Dry

cleaning without bag-type

filter is also possible.

Inflammable substances

must not be picked up

with the cleaner!

After picking up liquids,

the filter element is damp.

Damp filter elements can

clog more quickly when

dry substances are picked

up. For this reason, the

filter element should be

dried or replaced before

picking up any dry

substances.

PICKING UP LIQUIDS

Before picking up liquids,

the bag-type filter must

always be removed from

the tank.

Inflammable liquids

must not be picked up

with the cleaner!

If foaming is observed,

stop work immediately

and empty the tank.

SWITCHING ON THE

CLEANER

SQ 10/17 Gallon

SQ 10/15 Gallon RDF

SQ 10/15 Gallon RDFD

• Turn the switch to

position ‘I’ (Fig. 5).

SQ 10 Gallon AS/PE

SQ 17 Gallon AS/PE 2:

Two operating modes are

possible:

Switch position ‘I’:

The cleaner motor starts

immediately.

Switch position ‘auto’:

The cleaner motor starts

only when the tool

connected to the

appliance plug socket is

switched on (Fig. 6).

CAUTION!

Before turning the

switch to position

'auto', ensure that the

tool connected to the

appliance plug socket is

switched off.

The motor speed and thus

the suction power can be

varied at the suction force

regulator. This permits a

precise adaptation to

different substances to be

picked up (Fig. 6).

FILTER CLEANING

SQ 10/15 Gallon RDFD:

Warning light (Fig. 10)

indicates filter element is

in need of cleaning.

• Move filter cleaning

knob up and down.

This will move the ring

brush, cleaning the

filter element.

Option/model variant

ASSEMBLING THE

CLEANER

CAUTION!

On delivery, the

accessories - except the

extension tubes

(in the

packing of the cleaner) -

are lying in the tank and

must be removed before

the cleaner is used for the

first time.

Remove the cleaner top

section:

The power cord must not

yet be inserted into a plug

socket.

• Open the retaining

clamps and lift off the

cleaner top section

(Fig. 2).

• Place a bag-type filter

into the tank as

described in the

instructions (printed

on the filter).

• Fit the cleaner top

section and close the

retaining clamps.

• Connect the suction

hose. The 'Wap

MultiFit' enables any

Wap suction hoses

(27, 32, 36, 50 mm

diameter) to be

connected to the

cleaner.

(Fig. 3).

ELECTRICAL/

COMPRESSED AIR

CONNECTION

The operating voltage

shown on the rating plate

must correspond to the

voltage of the main power

supply.

• Ensure that the

cleaner is switched

off and insert the plug

of the power cord into

a properly installed

and fused plug socket

with ground.

CONNECTING ELECTRIC

TOOLS

SQ 10 Gallon AS/PE

SQ 17 Gallon AS/PE 2:

• Connect the electric

tool to the appliance

plug socket on the

control panel (Fig.4).

Before connecting a

tool, ensure that

both the cleaner and

the tool are

switched off.

For maximum power

consumption of the

electric tool to be

connected, see table

'Technical Data'.

CONNECTING

PNEUMATIC TOOLS

SQ 10 Gallon AS/PE:

• Connect the

pneumatic tool to the

quick coupler on the

control panel.

• Connect the

compressed air supply

to the nipple (Fig.4).

Option/model variant

PLEASE READ THE

OPERATING

INSTRUCTIONS AND

OBSERVE THE SAFETY

PRECAUTIONS!

INTENDED USE

When employed in

accordance with their

intended use, the

industrial vacuum cleaners

described in these

operating instructions are

suitable for picking up

non-flammable dry dusts

and liquids. They

correspond to dust class

'L'.

DESCRIPTION (Fig. 1)

1 Handle

2 Appliance switch

3 Suction force

regulator

4 Retaining clamp

5 Dirt tank

6 Inlet fitting

7 Compressed air

connection

8 Appliance plug socket

9 Compressed air

supply

10 Filter cleaning knob

11 Warning light

12 Base frame

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alto-WAP SQ 15 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alto-WAP SQ 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info