Bedienungsanleitung Amana A8TXNWFXB (Seite 5 von 42) (Englisch, Französisch, Spanisch)

506773

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

4. Tighten the compression nut. Do not overtighten. Reattach the

tube clamp and tube to the back of the cabinet.

5. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

6. The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in

the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill ice container.

Refrigerator Doors

TOOLS NEEDED: ⁵⁄₁₆" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat

2" putty knife.

IMPORTANT:

■ Before you begin, turn the refrigerator control OFF. Unplug

refrigerator or disconnect power.

■ Remove food and adjustable door or utility bins from doors.

■ If you are only removing and replacing the doors, see the

“Remove Doors and Hinges” and “Replace Doors and

Hinges” sections.

■ Depending on your model, you may have standard (Style 1) or

contoured (Style 2) doors. If you are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

Remove Doors and Hinges

⁵⁄₁₆" Hex-Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

4. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

5. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open

in the opposite direction, follow these steps. If you are not

reversing the doors, see “Replace Doors and Hinges.”

Style 1 - Standard

Graphics follow these instructions.

Cabinet

1. Remove ⁵⁄₁₆" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

A. Tube clamp

B. Copper tubing

C. Compression nut

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Door Stop Screw

Door Handle Sealing Screw

Flat-Head Handle Screw

Door Handle Seal Screw Front

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Door Handle Screw Cover

Round-Head Handle Scre

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amana A8TXNWFXB Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info