Bedienungsanleitung Amana AGR5844 (Seite 5 von 12) (Englisch)

506782

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

COOKTOP USE

Electric igniters automatically light the surface burners when

control knobs are turned to IGNITE.

Before setting a control knob, place filled cookware on the grate.

Do not operate a burner using empty cookware or without

cookware on the grate.

To Set:

1. Push in and turn knob counterclockwise to IGNITE.

IMPORTANT: All 4 surface burners will click. Only the burner

with the control knob turned to IGNITE will produce a flame.

2. Turn knob to anywhere between HIGH and LOW.

Power Failure

In case of prolonged power failure, the surface burners can be lit

manually. Hold a lit match near a burner and turn knob

counterclockwise to IGNITE. After burner lights, turn knob to

setting.

Sealed Surface Burners

IMPORTANT: Do not obstruct the flow of combustion and

ventilation air around the burner grate edges.

Burner cap: Always keep the burner cap in place when using a

surface burner. A clean burner cap will help avoid poor ignition and

uneven flames. Always clean the burner cap after a spillover and

routinely remove and clean the caps according to the “General

Cleaning” section.

Gas tube opening: Gas must flow freely throughout the gas tube

opening for the burner to light properly. Keep this area free of soil

and do not allow spills, food, cleaning agents or any other material

to enter the gas tube opening. Keep spillovers out of the gas tube

by always using a burner cap.

Burner ports: Check burner flames occasionally for proper size

and shape as shown above. A good flame is blue in color, not

yellow. Keep this area free of soil and do not allow spills, food,

cleaning agents or any other material to enter the burner ports.

To Clean:

IMPORTANT: Before cleaning, make sure all controls are off and

the oven and cooktop are cool. Do not use oven cleaners, bleach

or rust removers.

1. Remove the burner cap from the burner base and clean

according to “General Cleaning” section.

2. Clean the gas tube opening with a damp cloth.

3. Clean clogged burner ports with a straight pin as shown. Do

not enlarge or distort the port. Do not use a wooden toothpick.

If the burner needs to be adjusted, contact a trained repair

specialist.

4. Replace the burner cap, making sure the alignment pins are

properly aligned with the burner cap.

5. Turn on the burner. If the burner does not light, check cap

alignment. If the burner still does not light, do not service the

sealed burner yourself. Contact a trained repair specialist.

A. Burner cap

B. Burner base

C. Alignment pins

D. Igniter

E. Gas tube opening

WARNING

Fire Hazard

Do not let the burner flame extend beyond the edge of

the pan.

Turn off all controls when not cooking.

Failure to follow these instructions can result in death

or fire.

REMEMBER: When range is in use or (on some models)

during the Self-Cleaning cycle, the entire cooktop area may

become hot.

A. 1-1¹⁄₂" (25-38 mm)

B. Burner ports

A. Incorrect

B. Correct

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amana AGR5844 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info