Bedienungsanleitung Amana G-32026 PEKW (Seite 5 von 288) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

71318

Zoom out

Zoom in

Vorherige Seite

1/288

Nächste Seite

For pullout drawer only:

1. Turn both stabilizing

legs clockwise until

firmly against floor.

Turn roller

adjustment screws 2

to 3 times counterclockwise so that the full

weight of refrigerator rests on stabilizing legs.

2. Replace toe grille. See markings on inside of toe

grille to insure proper placement.

Roller Adjustment Screw

Stabilizing

Leg

Installation

4. Using the carpenter’s level, make sure front of

refrigerator is 6 mm or approximately one half

bubble higher than back of refrigerator and that

the refrigerator is level from side to side.

5. Turn stabilizing legs (C) clockwise until firmly

against floor.

6. Freezer drawer models only: Turn adjustment

screws (A) counterclockwise to allow the full

weight of the refrigerator to rest on the

stabilizing legs.

7. Replace the toe grille.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Snap bottom portion into place first. Press

down on top of grille until top portion snaps into

place.

2. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

3. Select models also have rear adjustment screws

(B). Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

Fresh Food Handles

Front Mount Handle - Style 1

Materials Needed:

• Phillips screwdriver

•

⁄16” hex head driver

To Install:

1. Remove 0.6 cm hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

• If reversing door, remove door plugs

from opposite side of door and

insert in screw holes.

2. Align handle holes with screw holes on

door face and secure with two door face

screws from step 1.

3. Locate handle trim in literature pack and

install over top and bottom of handle, as

illustrated.

• Secure top handle trim with remaining

screw removed in step 1.

• Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top

handle screw.

• Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

• Retain trim for later replacement.

3. Remove two hex head screws.

• Retain screws for later replacement.

Side Mount Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Remove screws from the side of the door.

2. Align the side mount handle with the pre-drilled

holes in the door panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amana G-32026 PEKW Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info