Bedienungsanleitung Amana NTW4700YQ (Seite 12 von 32) (Englisch, Französisch)

506798

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

TROUBLESHOOTING

If you experience Possible Causes Solution

Washer not performing as expected (cont.)

Washer not draining/

spinning, loads are

still wet or spin light

remains on (indicating

that the washer was

unable to pump

out water within

10 minutes)

Empty pockets and use

garment bags for small items.

Small items may have been caught in pump or between basket

and tub, which can slow draining.

Use a cycle with a low

spin speed.

Cycles with lower spin speeds remove less water than cycles

with high spin speeds. Use the recommended cycle/speed spin

for your garment. To remove extra water in the load, select Drain/

Spin. Load may need to be rearranged to allow even distribution

of the load in the basket.

The washer may be tightly

packed or unbalanced.

Tightly packed or unbalanced loads may not allow the washer

to spin correctly, leaving the load wetter than normal. Evenly

arrange the wet load for balanced spinning. Select the Drain/

Spin cycle to remove excess water. See “Using Your Washer” for

loading recommendations.

Check plumbing for correct

drain hose installation. Drain

hose extends into standpipe

farther than 4.5" (114 mm).

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening. Lower drain hose if the end is higher than 96" (2.4 m)

above the oor. Remove any clogs from drain hose.

Too much detergent causing suds to

slow or stop draining and spinning.

Always measure and follow detergent directions for your load.

To remove extra suds, select Rinse/Spin. Do not add detergent.

Dry spots on load

after cycle

High speed spins extract more

moisture than traditional top-load

washers.

The high spin speeds combined with air ow during the nal spin

can cause items near the top of the load to develop dry spots

during the nal spin. This is normal.

Incorrect or wrong wash

or rinse temperatures

Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water owing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Energy saving controlled wash

temperatures.

This washer uses cooler wash and rinse water temperatures

than your previous washer. This includes cooler hot and warm

washes.

Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water owing to the inlet

valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Using too much detergent. The suds from too much detergent can keep washer from

operating correctly. Always measure detergent and follow

detergent directions based on load size and soil level.

Washer not loaded as recommended. The washer is less efcient at rinsing when load is tightly packed.

Load garments in loose heaps evenly around the basket wall.

Load with dry items only.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 additional garments after washer has started.

Using too low a Load Size selection. Choose a Load Size that matches the load being washed.

Sand, pet hair, lint, etc.

on load after washing

Heavy sand, pet hair, lint, and

detergent or bleach residues may

require additional rinsing.

Select the Rinse/Spin cycle. Do not add detergent.

Load is tangling Washer not loaded as recommended. See “Using Your Washer” section.

Select a cycle with a slower wash action and spin speed; items

will be wetter than those using a higher speed spin. See the

“Cycle Guide” to match your load with the best cycle.

Load garments in loose heaps evenly around the basket wall.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

First try the solutions suggested here or visit our website at www.amana.custhelp.com -

In Canada www.amanacanada.ca for assistance and to possibly avoid a service call

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amana NTW4700YQ Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info