Bedienungsanleitung Ambrogio L250i Elite S plus (Seite 13 von 42) (Englisch)

733760

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

User’s manual

SETTING UP OF THE PERIMETER WIRE

Before installing the perimeter wire, it is necessary to check the

entire surface of the lawn. Make any necessary adjustments to the

grassy surface during the laying of the perimeter wire in order to

allow the robot to function correctly.

1. Evaluate the best method for returning to the charging station

according to the instructions described in the chapter “RE-

ENTRY METHOD TO THE CHARGING STATION”.

2. Evaluate whether a special installation of the perimeter wire

is necessary according to the instructions described in the

chapter “SET-UP OF THE ROBOT’S QUICK RE-ENTRY TO

THE CHARGING STATION”.

3. Preparation and dening of the work areas.

4. Installation of the perimeter wire.

5. Installation of the charging station and power supply unit. When

laying the perimeter wire, respect the installation direction

(clockwise) and the rotation direction around the owerbeds

(counter-clockwise), As shown in the gure.

track for laying the perimeter wire

RE-ENTRY METHOD TO THE CHARGING STATION

The robot can return to the charging station in two different ways

based on what is set in the user menu under the eld “Settings –

Re-entry to Base.” Use the “On the Wire” method only when there

are numerous obstacles inside the garden and near the perimeter

wire (within 2 meters). In all other cases it is better to use the

“V-Meter” method for the quickest re-entry to the charging station.

“Follow wire”. This method of re-entry to the charging station

commands the robot to follow the perimeter wire, positioning its

wheels on either side of the wire. If this method is activated, there

is no need to prepare the “Recall on Wire” as described below.

“V-Meter”. By setting this method of re-entry to the charging

station, the robot runs along the perimeter wire at an indicative

distance ranging from a few centimetres to one meter (3.2 '),

touching it every now and again in the curved sections until the

signal emitted by the charging station has been recognised for

guiding itself on the wire and entering correctly into the charging

station.

step

lower 2 mt.

5 cm.

2 mt.

10 mt. 1,5 mt.

charging

station

If narrow passages are present or the arrow for quick re-entry to the charging station, the wire must be positioned in a special

way, called “Recall on the wire.”

As soon as a “Recall” is recognised, the robot will follow the perimeter wire at low speed, and with more precision for around

10 meters (33 '). It will then return to the “V-Meter” re-entry mode if the quick re-entry or charging station was not encountered.

Follow these instructions to install the “Recall”:

•

the “Recall” is a piece of wire that extends for around 2 m (6.6 ') with a distance of 5 cm (1.96 ") between each wire;

•

the “Recall” must be positioned at a distance of 2 m. (6.6 ') in front of any narrow passages;

•

the “Recall” must be positioned in the section in front of the “Quick Re-entry”.

NB: If the robot does not nd the charging station within a certain amount of time, it will follow the perimeter wire in

“Follow wire” mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ambrogio L250i Elite S plus Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ambrogio L250i Elite S plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info