Bedienungsanleitung Ambrogio L30 de Luxe (Seite 27 von 46) (Englisch)

733769

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

User’s manual

SECONDARY AREAS – PROGRAMMING MODE

If the area to be mowed includes secondary areas based on the denition given in the chapter “Preparation and Marking the

Boundaries of the Work Areas”, then it is necessary to program the secondary areas so the robot knows how to reach them and

how many times.

SECONDARY AREA: function for dening the automatic mowing of a secondary area.

-Percentage: allows setting the dimensions of the secondary

area to be mowed in respect to entire lawn surface. Below is a

table to use as a guide for conguring a secondary area:

• 10% indicates a very small area.

• 30% indicates an area which is approximately one third of

the entire garden.

• 50% indicates an area which is approximately half of the

entire garden.

• 80% indicates a secondary area which is bigger than the

primary area.

• 100% the robot will follow the perimeter wire to mow the

secondary area each time it exits the charging station.

primary area

clockwise directionanti-clockwise direction

secondary area 1

(30%, 60MT, clokwise)

secondary area 2

(20%, 30MT, Anti-clokwise)

-Distance: this allows setting the distance necessary for the robot to reach the internal part of the secondary area following

the perimeter wire. It is recommended to measure half the distance of the secondary area to ensure that the robot starts

working inside that area.

-Direction: indicates the shortest direction for reaching the secondary area. The direction can be clockwise or counter-

clockwise. The robot exits from the charging station and follows the wire in the indicated direction to reach the secondary

area.

-Mode: indicates the method for reaching the secondary area. Use the “Follow wire” method when there are lots of obstacles

in the garden close to the perimeter wire (less than 2 m) or when there are tight areas to pass through (less than 2 m) to reach

the secondary areas. In all other cases use the “V-Meter” method.

• “Follow wire”. The robot reaches the secondary area positioning its wheels astride the perimeter wire.

• “V-Meter”. The robot reaches the secondary area running along the perimeter wire at an indicative distance from a few

cm to 1 m (3.2 ')..

SECONDARY AREA 2: function for dening the automatic mowing of secondary area number 2. This setting uses the same

conguration parameters as those used for secondary area 1.

SECONDARY AREA 3: (only for some versions, see “Technical Specications”). Function for dening the automatic mowing of

secondary area number 3. This setting uses the same conguration parameters as those used for secondary area 1.

SAFETY – PROGRAMMING MODE

CHANGE PASSWORD: function for setting or changing the password.

-No: the password entered does not need to be changed.

-Yes: for entering or changing the password which will be used to start the robot. You will prompted to enter the following

information:

• password: enter the old password (manufacturer’s default 0000).

• new password: enter the new password. The password must be different from 0000.

• repeat password: enter the new password again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ambrogio L30 de Luxe Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ambrogio L30 de Luxe

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info