Bedienungsanleitung Amica ZWM 496W (Seite 7 von 24) (Englisch)

794715

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

INSTALL THE APPLIANCE

Placement of the product

• When choosing the place of installation,

make sure you will be able to easily load and

remove dishes and utensils from the dish-

washer.

• Do not place the appliance in a room where

the temperature can fall below 0°C.

• Before installing unpack the appliance follow-

ing the instructions on the packaging.

• Place the appliance close to the water valve

and drain. When installing the dishwasher as-

sume that the connection will not be changed.

• When you move the appliance do not handle it

by the door or control panel.

• Leave some room on all sides to have

convenient access to the dishwasher when

cleaning.

• Make sure that when you set the dishwasher

you do not crush the water supply and drain

hose. Also, make sure that the appliance is

not places on the power cord.

• Level the appliance using the adjustable legs.

Proper level ensures trouble-free opening and

closing the dishwasher doors.

• If the dishwasher door will not close properly,

check that the appliance stands rmly on the

oor, if not, adjust using the adjustable legs.

Water supply connection

Make sure that domestic water supply system is

suitable for the dishwasher. It is recommended

to install a lter in the water supply line to avoid

damage to the appliance due to impurities (such

as sand, clay, rust, etc.) that occasionally occur in

water. This will also prevent accumulation of sedi-

ment after dishwashing.

Water supply hose

Do not use the water supply hose from the old

dishwasher. Use the new water supply hose

provided with the appliance. Before connecting,

rinse the hose with water. Connect the water sup-

ply hose directly to the

water feed valve. The

domestic water system

pressure should be at

least 0.03 MPa and up

to 1 MPa. If the water

pressure exceeds 1

MPa, install pressure

reducing valve.

When the connection is

ready, open the valve

completely and check

for leaks.

For safety reasons,

close the water supply

tap after every wash.

NOTE: Aquastop water supply is used in

some dishwasher models. Dangerous volt-

age could occur with Aquastop. Do not cut

the Aquastop water supply. Do not allow it

to bend or twist

The drain hose

The drain hose can be connected directly to a

water drain or kitchen sink stub pipe. You can also

drain the water directly into the sink using the spe-

cial bracket (if available), placing the drain hose

outlet on the kitchen sink edge. The drain hose

connection should be made at least 50 cm and up

to 110 cm from the oor.

If the drain hose is longer than 4 m, dishes

may not be washed properly. The manu-

facturer is not be held responsible for such

a situation

Important!

For safety reasons, close the water tap

after every wash

min 50cm/max 110cm min 50cm/max 110cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Amica ZWM 496W Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info