Bedienungsanleitung Ampeg SVT-8 Pro (Seite 6 von 9) (Englisch)

541773

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

The Rear Panel

SVT-8 PRO Bass Amplifier

20. AC LINE IN: Firmly insert the supplied AC

power cord into this socket until it is fully seat-

ed. Plug the male end of the cord into a

grounded AC outlet. DO NOT DEFEAT THE

GROUND PRONG OF THE AC PLUG!

21. BAL. OUT: This jack supplies a line level

signal for connection to a house mixing board,

recording console or external amplifier. The sig-

nal level at this jack is governed by the Post/Pre

switch (#23).

22. GND/LIFT: Use this switch to lift the ground

connection at the Bal. Out jack to help eliminate

hum in the Bal. Out signal.

23. POST/PRE: The signal at the Bal. Out jack

(#21) can be set to either Pre or Post-EQ with

this switch. With the swi

tch in the OUT position,

the signal at the jacks is Pre-EQ. This is a direct

output not affected by any EQ or boost settings.

With the switch depressed, the signal is Post-

EQ and is controlled and modified by the tone

controls and the effects loop.

24: TUNER OUT: This jack is provided for con-

nection to an electronic tuner and is always

“live,” even when the Mute switch (#3) is

engaged. This allows for “silent tuning” as well

as a monitor feed which stays hot even when

the house mix is muted.

25. SPEAKERS: These output jacks supply

speaker-level power to the speaker cabinet.

The rated power output is 1300 watts rms

into 4 ohms or 2500 watts rms into 2 ohms

(minimum load).

WARNING: Use speaker cables to make

the connections. Do not use instrument

cables as they may overheat.

Pin 1+ = hot

Pin 1– = return

26. CIRCUIT BREAKER: The SVT-8 PRO

employs an AC line circuit breaker to

help pro-

tect against damages due to excessive current

demands. If the amplifier stops working, check

the circuit breaker.

27: POWER AMP IN: This jack connects an

external preamp directly to the power amp.

When using an external source, connect the

output of the source to this jack by means of a

shielded signal cable to feed the signal into the

power amp section. The internal signal is dis-

connected when a connector is inserted into

this jack.

28. PREAMP OUT: Use this jack to send a sig-

nal from the internal preamp to an auxiliary

power amplifier, mixing console, monitor sys-

tem, or

house PA system. The signal at this

jack is post-EQ.

29. EFFECTS LOOP RETURN: When using

an external signal processor, connect the out-

put of the device to this jack by means of a

shielded signal cable.

30. EFFECTS LOOP SEND: When using an

external signal processor, connect this jack to

the input of the device by means of a shielded

signal cable.

31. FOOTSWITCH: Connect a two-button

(ring/tip/sleeve) footswitch to this jack to control

the Power Reduction and the Mute functions.

(Mute = tip/sleeve; Power Reduction = ring/

sleeve.)

NOTE: A footswitch may be purchased at

your local Ampeg Dealer or ordered directly from

LOUD Technologies Inc. Be sure to ask for

model #AFP2.

IMPORTANT: This unit employs forced air

cooling by means of an internal fan. The

rear and side ventillation slots must remain

unobstructed when operating this amplifier.

When mounting the unit in a rack make sure

there is ample room for proper air circulation.

The rack must be constructed and positioned

in such a manner to allow proper air flow and

the exhausting of hot air away from the rack

at all times.

WA R NING :

Made In T he U.S .A .

L OUD T E CH NOL OG IE S, INC .

100Ð240V 50/60Hz 300VA

250 0W @ 2 O HMS

130 0W @ 4 O HMS

C LA SS 2 W IR ING

T his device c ompli es with pa rt 15 of th e F CC R ule s.

Op erati on is su bjec t to the follow ing two c ond ition s:

this devic e m ay not c au se ha rmfu l in terferenc e, and this

dev ice mu st acc ept any in terfe renc e r ec eive d, i nclu ding

inte rfer enc e th at m ay ca us e u ndes ir ed o pera tion .

26 27 28 3129 30

20 2421 2522 23

26 27 28 3129 30

20 2421 2522 23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ampeg SVT-8 Pro Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info