Bedienungsanleitung Angelcare AC517 (Seite 3 von 64) (Englisch, Französisch, Spanisch)

681989

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

12.14 Overloading - DO NOT overload wall outlets, extension cords or

integral convenience receptacles as this can result in a risk of ﬁre or

electric shock.

12.15 Object and Liquid Entry - NEVER push objects of any kind into this

product through casing slots as they may touch dangerous voltage points

or short out parts that could result in a risk of ﬁre or electric shock. NEVER

spill liquid of any kind on the product.

12.16 Antenna - e antenna used for this transmitter must be installed

to provide a separation distance of at least 20 cm from all persons and

must not be collocated or operating in conjunction with any other antenna

or transmitter.

12.17 Power Lines - An outside antenna system should NOT be located

in the vicinity of overhead power lines or other electric light or power

circuit, or where it can fall into such power lines or circuits as contact

with them may be fatal.

12.18 Vibration Source - When the monitor is in use, DO NOT use a bedside

crib, crib mobile or other crib accessories that may produce vibrations.

Other sources of vibrations may include fans, washing machines, loud

music, etc. ese sources of vibration may interfere with the performance

of your Angelcare

monitor and the alarm will not sound if it continues to

detect any movement other than your baby’s. Be sure all vibration sources

are eliminated before using the monitor.

12.19 You may experience false alarms for several reasons. The

most common reason is the Camera has not been turned OFF

after you have removed your baby from the crib. Another reason is

the Sensor Pad has not been placed under the mattress properly.

Be sure the Sensor Pad is on a ﬂat, ﬁrm surface with the Angelcare

logo

side facing up. e sensitivity level may also need to be adjusted. Refer

to Step 5.1. Always be sure to immediately check on baby whenever an

alarm sounds.

12.20 Sensor Pad - Your Sensor Pad can be used in any crib that is stationar y.

If the crib has a spring or slat base, place a hard board between the crib

base and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.

Only use your Angelcare

monitor in a stationary sleeping environment such

as a crib where the Sensor Pad can rest on a completely ﬂat, ﬁrm surface.

The Sensor Pad is made of plastic and does not permit the

air to circulate. Therefore, mildew build up could develop

underneath the mattress in the Sensor Pad area. We suggest

rotating the mattress regularly to prevent any mildew.

13. IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES

13.1 Use ONLY the type and size of battery speciﬁed in the owner’s manual.

ere is a risk of explosion if battery is replaced with an incorrect type.

13.2 Charge the battery for 9 hours prior to ﬁrst use. Be sure to have the

monitor in the OFF position during this period. ONLY use the adapters

included with your monitor.

13.3 DO NOT use these adapters with any other equipment.

13.4 When unplugging the adapter from the Camera, be sure it is switched

to the OFF position.

13.5 DO NOT dispose of batteries in ﬁre. ey may explode. Check with

local regulations for possible special disposal instructions.

13.6 Exercise care in handling batteries in order not to short out the

batteries with conducting materials such as rings, bracelets and keys.

Overcharging, short circuiting, reverse charging, mutilation, or incineration

of batteries must be avoided to prevent one or more of the following

occurrences: release of toxic materials, release of hydrogen and/or oxygen,

gas and rise in surface temperature.

13.7 DO NOT attempt to rejuvenate the battery provided with or identiﬁed

for use with this product by heating them. Sudden release of battery

electrolyte may occur, causing burns or irritation to eyes or skin.

13.8 If and when necessary, the battery must be replaced with identical

new ones or equivalent (volts and size).

13.9 Remove the battery from the Parent Unit if you store the product

over 30 days because the battery could leak and damage the product.

13.10 Discard ‘dead’ batteries as soon as possible since ‘dead’ batteries

are more likely to leak in a product. If a battery has leaked or vented, it

should be replaced immediately using protective gloves.

13.11 DO NOT store this product, or the battery provided with or identiﬁed

for use with this product, in high-temperature areas.

WARNING (North America Only)

14. Modiﬁcations not authorized by the manufacturer may void users

authority to operate this device.

14.1 NOTE: is equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

ese limits are designed to provide reasonable protection against harmful

interference in a residential installation. is equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications.

14.2 However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

14.3 is device complies with the part 15 of the FCC Rules and the

Industry Canada license - exempt RSS standards(s). Operation is

subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) is device must accept any interference received, including

interference that may cause undesired operation.

IC Warning :

15. is device complies with industry Canada RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including inferences that

may cause undesired operation of the device.

15.1 Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

Model AC417 and AC517

Baby Breathing Monitor, with Video

SETUP REQUIREMENTS

INCLUDED:

Touchscreen Parent Unit

Tabletop stand with removable

wall mount metal ball

(for Camera Unit)

Hardware

(Screwdriver required

for wall mounting)

Wireless movement Sensor Pad

* Always place Angelcare

logo side up *

Lithium ion

battery pack

(for Parent Unit)

2x AC adapter

(for Parent Unit and

Camera Unit)

CR3032 battery

(for Sensor Pad)

Camera Unit

256AC_07_Manuel_AC517_NA_m4.indd 3 2018-08-15 10:15 AM

Angelcare AC517 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Angelcare AC517

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info