Bedienungsanleitung Apa 16443 Power Pack (Seite 10 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

807560

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

6. OPERATING INSTRUCTIONS

6.1 OVERVIEW

Press the switch once (Position 1 in the overview).

The display (Position 2 in the overview) is activated and

shows the charging level of the Powerpack as a

percentage (Position 13 in the overview).

6.2 CHECKING THE CHARGING LEVEL OF

THE POWERPACK

6.3 CHARGING THE POWERPACK

Use a USB charger with a 2 A output to charge the

Powerpack (not included in delivery!). Insert the USB-C

connector of the charging cable (Position 11 in the

overview) into the USB-C input (Position 3 in the

1 Switch

2 Display

3 USB-C input

4 USB output

5 LED light

6 EC5 starting help

connection

7 Control lamp Smartbox

Figure 1: Overview

8 Smartbox jump lead

9 Terminal clamp, black (-)

10 Terminal clamp, red (+)

11 USB-C charging cable

12 Bag

13 Charging level in %

14 Voltage

15 Current

16 Input / output

overview) of the Powerpack. Insert the USB-A

connector of the charging cable into the charger.

Connect the charging device to a socket.

The display shows the charging progress as a

percentage, 1% - 99%. At 100%, the battery of the

Powerpack is completely charged.

After charging, rst remove the charger from the socket

and then disconnect the charging cable from the charger

and the Powerpack.

6.4 JUMP START FOR 12 V VEHICLES

1. Switch o the ignition and all consumers on your

vehicle.

2. Ensure that the battery capacity of the Powerpack is

still at least 75% and that the battery callipers of your

vehicle battery are not soiled or oxidised.

3. Connect the Powerpack and the jump lead by

inserting the connector of the Smartbox (Position 8 in

the overview) of the jump lead into the starting help

connection (position 6 in the overview) of the Power-

pack. The LED light (Position 5 in the overview) is acti-

vated. Ensure that the connector is inserted rmly and

securely. The control lamp (Position 7 in the overview)

of the Smartbox ashes alternately red/green.

4. First connect the red terminal clamp (Position 10 in

the overview) of the jump lead with the positive pole,

and then the black terminal clamp (Position 9 in the

overview) with the negative pole of the vehicle bat-

tery. The terminal clamps must have a rm and secure

contact to the battery poles.

5. If the jump leads are connected correctly, the control

lamp shines green permanently, and a single tone is

issued.

Figure 2: Control lamp Smartbox

6. Start the vehicle motor. Do not operate the starter for

longer than 3 seconds. If the starting attempt was not

successful, wait at least two minutes before trying

again. After a third failed attempt, do not start a fur-

ther attempt and instead check your vehicle for faults.

7. Disconnect the jump lead from the Powerpack. Then

remove the terminal clamps from the vehicle battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Apa 16443 Power Pack Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info