Bedienungsanleitung Apa 16540 - SH317 (Seite 11 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

807554

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

The starter aid function of the power

pack is only for vehicles with 12 V on-

board voltage. Before you start, read the

operating instructions of your vehicle, if

and how and external starter aid can be

used. Modern vehicles have sensitive

electronics and control devices that can

be damaged when handled incorrectly.

The control LED (position 5 in the overview) is now red.

For the initial charging process, leave the power pack

connected for 24 hours. For all subsequent charging

processes or directly after use charge no longer than

20 hours. Once the battery is fully charged, the LED is

green. After the charging process,  rst pull out the plug-

in charger from the socket and then unplug the coaxial

power connector from the charging socket of the power

pack. Now close the charging socket with the sealing

plug. If you press the battery test switch now, the control

LED is green.

6.2.2 CHARGING WITH THE 12V MOTOR VEHICLE

CHARGING CABLE

Turn the on-o switch (position 1 in the overview) to

the OFF position. Plug the coaxial power connector of

the cigarette lighter charging cable (position 12 in the

overview) into the charging socket of the power pack

(position 6 in the overview). Now plug the 12V vehicle

plug into the 12V socket of your vehicle. The control LED

(position 5 in the overview) is now red. Charge the power

pack for approx. 6 – 8 hours.

Make sure that the power pack is fully charged. To do so,

press the battery test switch (position 4 in the overview).

Once the control LED is green (position 5 in the overview),

the power pack is ready for use.

Once the battery is fully charged, the LED is green. After

the charging process,  rst pull out the 12V vehicle plug

from the socket of your vehicle and then unplug the

coaxial power connector from the charging socket of

the power pack. Now close the charging socket with the

sealing plug. If you press the battery test switch now, the

control LED is green.

Only charge the power pack while

driving or when the engine is running,

otherwise there is a risk of discharging

the starter battery of your vehicle.

6.3 STARTER AID

CAUTION

Start the engine. Do not let the starter motor work longer

than 6 s. The battery of the power pack is not suitable for

longer start attempts. Between start attempts, take a

break of at least 5 minutes. If the engine doesn‘t turn on

after several attempts, discontinue using the starter aid

and look for the cause of the malfunction.

Now turn the on-o switch to the OFF position. First

remove the black (-) terminal clamp, roll up the cable

and fasten the terminal clamp to its designated holder.

Then remove the red (+) terminal clamp, roll up the cable

and fasten the terminal clamp to its designated holder.

Always adhere to this sequence.

Recharge the power pack.

Turn o the ignition of your vehicle as well as all electrical

consumers (radio, light, rear window heating, seat

heaters, etc.). Enable the parking brake.

Turn the on-o switch (position 1 in the overview) to the

OFF position. First connect the red (+) terminal clamp

(position 11 in the overview) to the positive terminal of

your vehicle battery. Connect the black (-) terminal clamp

(position 10 in the overview) as far away from the battery

as possible to the engine block or chassis (no painted parts).

If the power pack is properly connected, the reverse polarity

protection view is lit green (position 2 in the overview). If

this is not the case, the reverse polarity protection view is lit

red and a warning signal is sounded. In this case, check the

connection of the terminal clamps and correct it. Now turn

the on-o switch to the ON position.

6.3.2 START ATTEMPT

6.3.3 REMOVING THE POWER PACK

6.3.1 CONNECTING THE POWER PACK

VEHICLES WITH NEGATIVE EARTH

In order to be able to work with the compressor,  rst take

the air hose (position 7 in the overview) out of the holder.

To do so, you brie y have to remove the red (+) terminal

clamp from its holder.

6.4 COMPRESSOR

Open the lock on

the valve connector

Place the valve

connector on the valve

6.4.1 FILLING A TYRE WITH THE CAR

VALVE / SCHRADER VALVE

Öffnen Sie die

Verriegelung

am Ventilanschluß

Setzen Sie den

Ventilanschluß auf

das Ventil

Verriegeln Sie den

Ventilanschluß

Sie können jetzt

den Reifen mit dem

Kompressor

befüllen

Fig. 2 Fig. 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Apa 16540 - SH317 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info