807545
9
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
9
6.2.2 CHARGING THE POWER PACK WITH THE MOTOR
VEHICLE CHARGING CABLE
Make sure that the Power Pack is switched o . All control
lights and the work light must not be illuminated. Switch
o the compressor. Plug the coaxial connector of the motor
vehicle charging cable (Position 19 in the overview) into the
charging socket of the Power Pack (Position 9 in the over-
view). Now plug the motor vehicle charging cable into the
12 V on-board socket in your car. The charge status display
(Position 7 in the overview) is activated, and  ashes. If all
three lights on the charge status display are always lit, then
the Power Pack battery is fully charged. After charging,
rst disconnect the motor vehicle charging cable from the
on-board socket, then disconnect the coaxial connector from
the charging socket of the Power Pack.
6.2 CHARGING THE POWER PACK
Fully charge up the Power Pack after purchase with the plug
charger before initial use (Section 6.2.1)
CAUTION
Only charge the Power Pack when driving
or when the motor is running, otherwise
there is a risk that the starter battery of
your vehicle may be discharged.
Make sure that the Power Pack is switched o . All control lights
and the work light must not be illuminated. Switch o the
compressor. Plug the coaxial connector of the plug charger
(Position 18 in the overview) into the charging socket of
the Power Pack (Position 9 in the overview). Now, connect
the plug charger with the mains socket. The charge status
display (Position 7 in the overview) is activated, and  ashes.
If all three lights on the charge status display are always lit,
then the Power Pack battery is fully charged. After charging,
rst disconnect the plug charger from the mains socket, then
disconnect the coaxial connector from the charging socket of
the Power Pack.
6.2.1 CHARGING THE POWER PACK: WITH THE PLUG
CHARGER
6.3 STARTING AID
For instructions on carrying out a jump
start, read the manual of your vehicle or
ask your specialist workshop.
Disconnect all of the devices connected to the Power Pack
from the 12 V outlet socket (Position 6 in the overview) and
from the USB port (Position 11 in the overview).
Make sure that the Power Pack is fully charged. To do this,
press the ON/OFF switch (Position 8 in the overview). If all
three lights are illuminated on the charge status display
(Position 7 in the overview) then the Power Pack is ready to
use.
6. OPERATING INSTRUCTIONS
6.1 OVERVIEW
Figure 1: Overview
1 Handle
2 Control panel front
3 LED indicator  eld
4 Jump lead (+)
5 Jump lead (-)
6 12 V outlete
7 Charge status display
8 Switch
9 Charging socket
10 USB control light
11 USB port
12 Compressor switch
13 Manometer
14 Rear side of control panel
15 Pole calliper (-)
16 Air hose storage
compartment
17 Pole calliper (+)
18 Plug charger
19 Motor vehicle charging cable
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Apa 16553 - TMSPL-28 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info