Bedienungsanleitung Apa 16644 Powerpack Bully Smart (Seite 6 von 16) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

807548

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

with plenty of soap and water!

• Never wear rings, necklaces, watches or similar

when handling batteries or chargers. The short-

circuiting of the battery contacts brings a risk of

burns and explosion!

• The power pack is only designed as a jump-start

for a vehicle that has a battery of its own. The

power pack cannot replace the vehicle battery.

• Always store the pole callipers in the designated

holders to ensure that the power pack is not at

risk of short-circuiting when not in use.

• Never attempt to jump-start a vehicle when the

battery is frozen, this brings a risk of explosion.

• Always observe the following sequence

when disconnecting the power pack from the

battery. There is a risk of explosion: Switch o

the jump-start function on the Power Pack. First

disconnect the black (-) pole calliper, coil the

cable and attach the pole calliper to the

designated holder. Then disconnect the red (+)

pole calliper, coil the cable and attach the pole

calliper to the designated holder.

6. MANUAL

6.1 OVERVIEW

1 Pole clamp (+) red

2 Rotary switch jump-start

3 Charging indicator light

4 Control lamps for charging status

5 12 V sockets

6 Push-button switch charging status

7 USB output with control lamp

8 ON/OFF switch USB connection

9 Storage compartment 230 V charging cable

10 Pole clamp (-) black

6.2 CHARGING THE POWER PACK

Charge the power pack for 24 hours before you use it for the

 rst time. To do this, place the power pack in a well-ventilated

location. Open the storage compartment for the 230 V char-

ging cable (Position 9 in the overview) and remove the char-

ging cable. Insert the plug of the cable into a 230 V socket. The

charge control lamp (Position 3 in the overview) now lights in

red. After 24 hours, disconnect the mains plug, stow the cable

in the storage compartment without kinking and close the lid.

Press the push button (Position 6 in the overview) for the char-

ging status indicator (position 4 in the overview). If the green

control lamp lights up, the power pack is ready for use.

In order to ensure that the power pack is always able to provi-

de its full power performance, charge for at least 5 hours after

each use (to jump-start a vehicle).

6.3 CHECKING THE CHARGING STATUS

The charging status of the battery cannot be checked during

charging. First disconnect the 230 V charging cable from the

socket before checking the charging status.

To check the charging status of the power pack, press the but-

ton for the charging status (Position 6 in the overview) while

the mains is unplugged. The indicator lights for the charging

status (Position 4 in the overview) indicate the status of the

battery:

Low (red): The battery must be charged as soon as

possible

Middle (yellow): Charging the battery is recommended

High (green): It is not necessary to charge the battery

The jump-start function of the power pack

is designed only for vehicles with a 12 V

on-board voltage. Before using, consult

the operating instructions of your vehicle

to determine whether, and if so, how an

external jump-start is to be used. Modern

vehicles have sensitive electronics and

control devices that may be damaged if the

wrong procedure is used.

6.4 JUMPSTART

Make sure that the power pack is fully charged. To do this, press

the control button for the charging status (Position 6 in the

overview). If the charging control lamp (Position 4 in the over-

view) lights up „high“ green, the power pack is ready for use.

Figure 1: Overview

6.5 CONNECTING THE POWER PACK VEHICLES WITH

NEGATIVE EARTH

Switch o the ignition and all electrical consumers of the

vehicle (radio, lights, rear window heating, seat heating etc.).

Apply the parking brake.

Make sure that the power pack‘s jump-start

rotary switch (Position 2 in the overview) is

set to „OFF“.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Apa 16644 Powerpack Bully Smart Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info